Solight TE44 Скачать руководство пользователя страница 2

Setting the alarm 
 

1.  Briefly press the "ALARM" button in order to enter alarm mode.

 

2.  In alarm mode, press and hold the "ALARM" for longer than 2 seconds. That way you will enter alarm setting mode and the 

active section of the display will begin flashing.

 

3.  You can change settings using the "UP" or "DOWN" buttons. By pressing and holding one of these buttons for longer than 2 

seconds you will be able to change values at approx. 5 steps per second.

 

4.  By briefly pressing the "ALARM" button you can save the set value and continue to setting the next parameter.

 

5.  If you do not press any button for 20 seconds, the currently displayed value will be saved and the display will toggle into 

standard display mode.

 

6.  You can activate the alarm in alarm mode by briefly pressing the "ALARM" button. The bell symbol 

 will appear on the 

display, indicating an active alarm. 

7.  The alarm is equipped with a delayed alarm function, so-called "SNOOZE". At the moment the alarm begins to ring, press the 

"SNOOZE" button in order to put off the alarm for 5 minutes. The bell symbol 

 will begin flashing. By pressing any other 

button you can turn off the alarm for 24 hours. 

 
Measuring temperature 
 

1.  The exact indoor temperature is automatically displayed within 3 to 8 minutes of inserting the battery.  
2.  The outdoor temperature is displayed only after receiving the signal from the wireless sensor. The sensor will begin to work 

properly approx. after three minutes of inserting the battery. Until that time it is possible that the outdoor temperature is not 
displayed accurately. 

3.  By repeatedly pressing the "Max./Min." buttons you can display measured values in the following order: minimum temperature 

> maximum temperature > current measurement. 

4.  When in max. or min. temperature display mode you can delete all saved temperature data by holding the "Max./Min." button. 
5.  By briefly pressing the "DOWN/CF" you can toggle the temperature display between 

°C and °F. 

 

Caution: 

1.  When performing interval measurements of temperatures far below zero, e.g. -

20°C and less, it is necessary to wait a longer 

period of time than with constant measurement. The wireless sensor will reflect drops in temperature relatively rapidly to the 
thermometer during the first phase of measurement; however, precision results will be achieved only after a certain period, 
sometimes as long as 6 hours. This applies in cases when you have removed the sensor from room temperature to freezing 
temperatures. If the sensor is continuously outdoors, however, the temperature will change periodically and will not result in 
the discrepancies mentioned above. 

2.  Direct sunlight and other heat sources have a negative effect on the measured temperature. 
3.  At temperatures around -

30°C and below, the cordless sensor will cease to display temperature information on the LCD 

display for reasons of saving battery power for enhancing performance. The wireless connection with the main unit will remain 
active. If the main unit does not display the outdoor temperature, try restarting the connection

– see below. At lower 

temperatures it is important to have fully charged, high quality batteries - for these cases, alkali only. Long-term exposure of 
batteries to very low temperatures will rapidly reduce their capacity and endurance. 

 

Receipt of high-frequency signal 
 

  the sensor works at a frequency of 433MHz 

  the reach of the signal is approx 80 m in open space 

  the main unit should display information from the sensor within three minutes 

  if wireless transmission is disrupted, you can restart the connection by pressing and holding the "UP" button 

 

Troubleshooting

 

 
The main unit does not display data from the wireless sensor: 
 

  make sure that there is no interference from any other electrical device or metal object, or that your neighbour is not using a 

device on the same frequency, for example 

  make sure that the distance of the sensor from the main unit does not exceed 80 m in open space 

  make sure that two correct batteries of the same type have been properly inserted, and that they are fully charged 

  the outdoor temperature is too low or too high and is at the extremes of device sensitivity. 

 
 

 
 
 

A CE Declaration of Conformity has been provided to the product in accordance with applicable regulations. Available upon request 
from the manufacturer: info@solight.cz, or available for download at shop.solight.cz. 
Manufacturer: Solight Holding, s.r.o., 

Na Brně 1972, Hradec Králové 500 06, Czech Republic 

Отзывы: