Power supply
Batteries – use exclusively 1.5V alkaline batteries. 1.2 V rechargeable batteries are insufficient for device operation. Especially
when using partially discharged rechargeable batteries, the display intensity may be reduced and the device will interpret this
condition as result of discharged batteries. When the batteries are low, an icon will flash on the display. In that case immediately
replace batteries with new ones.
Notes
1. To achieve the most accurate results, we recommend you to clean the testing chamber with utmost care from previous
blowing, especially in case of repetitive subsequent measuring cycles. This can be done by shaking the device in your hand,
following the direction of the blow-in mouthpiece a few times in both directions. A perfect cleaning can be achieved by fresh
air stream - e.g. using a fan.
2. Powering the device off using push-button or automatically after 30 seconds means that the device will turn into stand-by
mode. If you know that you won’t use the device for a longer period of time and wish to avoid slow battery discharging,
remove them from your device.
3. If the tester has not been in use for a prolonged period, the results of the first two tests may differ from actual values. If the
difference between two measurements exceeds 0.1 ‰, you should carry out one more measurement.
4. When blowing into the device, do not obstruct air outlet from the device – this would cause inaccurate measurement.
Storage and use
1. Store the device in dry environment without the presence of chlorine or corrosive gases, within the prescribed temperature
range.
2. Storage in low temperatures will make device activation last longer.
3. Do not let the device fall down on the ground or expose it to impacts and vibrations. In the event of damage by dropping, the
device is irreparable.
4. For cleaning, use dry cloth and avoid using abrasive agents or solvents.
5. !!! Measuring immediately or shortly after drinking alcohol is inaccurate and usually also causes damage to the measuring
sensor. Claim due to this cause would be unjustified.
6. Fuel Cell technology – used by professionals and the police all over the world. The sensor consists of several thin plates
coated with microscopic platinum layers. The electrochemical reaction on the sensor surface determines the alcohol content
according to precise calculation formulas stored in the device chip. As platinum gets into contact with ethanol contained in
alcoholic drinks but also due to humidity and various gases contained in the air, the sensor surface will oxidise. Oxides are
removed by calibration. According to the regulations and standards, the device should be re-calibrated every 12 months.
7. Also, the device will get locked after 500 measurement; “LOCK” text will appear on the display and it must be re-calibrated
by a specialized workshop. Doing this will preserve the measuring sensor, extend its service life and ensure measurement
accuracy – all due to oxidation on its surface.
Calibration is charged according to the current price list of Solight holding
s.r.o.
8. Under usual conditions, the service life of the Fuel Cell sensor is longer than 3 years. The sensor integrated in this device is
made by a specialized lab in the UK.
Warning:
Despite its accuracy, the 1T06 Digital Breath Analyser should be only used as a general guide for detecting alcohol level in your
body. Precise values can be only obtained by blood taking.
The level of alcohol in breath can be affected by a number of factors (such as gases in air, smoke, several mouth odours etc.).
Therefore, the measured values are merely approximate. The test result should not be interpreted as an indisputable ground for
determining the safe capability of driving, running equipment or carrying out other dangerous activities. Neither the seller not the
manufacturer accept any liability resulting from the use of this device. DO NOT DRINK ALCOHOL BEFORE DRIVING! Technical
parameters are subject to change without prior notice!
Technical data
1
Measurement range:
0.000 ‰ ~ 4.000 ‰,
measuring accuracy ± 0,008 ‰
2
Power supply:
3 pc. of 1.5V
alkaline
AAA batteries
3
Display:
digital with backlight
4
Standby mode:
approx. 30 seconds after the latest test
5
Length of measured breathe-out:
approx. 5-7 seconds of uninterrupted air flow
6
Dimensions:
112 x 62 x 20 mm
7
Weight:
85g (without batteries)
8
Pre-set warning value:
0.2‰ BAC, memory for 20 measurement values
9
Standard:
CE
10
Accessories:
2 pc. of blow-in tubes
11
Operating temperature:
0
℃
/ +55
℃
