background image

ADA102mpx.   If   you   don't   have   a
modulation   meter,   do   not   change   this
preset.

Do not push the screwdriver. The preset can be broken.

The level knob at the ADA102mpx front panel do not
changes the MPX level. Only take effect on the level of
balanced outputs, so it must be adjusted only to obtain
a visualization at the VU-meters, which will indicate
that 

input streaming is present

.

The   internal   input   gain   (software)   do   not   be
changed. It must be -1 dB (default value).

1.4.2.2 Full digital connections

Whenever the audio processor is located, in a full
digital audio chain 

– case (b) mentioned above –

 the

controls on frontal panel do not take effect over the
signal.   The   adjustment   is   made   from   web   control
panel.  The level of the digital audio is not changed
by the encoding–decoding process. 

You must set the output level of the decoder

output (wich excites the stereo coder input)

according  to   the  output  level  (dBfs)  of   the

audio processor.  Default output level is -1 dB

(for use with analog signals).

This   level   is   adjusted   from   web   control

pannel,   in   the   section  

Basic   Settings   →

Configration → Audio

 

(Output Audio Level)

.

Next,   a   table   with   reference   Output   Audio

Level values.

Procesador output

(dBfs )

Decoder Output

- 3 dBfs

 - 6 dB *

- 6 dBfs

 - 3 dB

- 9 dBfs

  0 dBfs

* Value for Solidyne digital processors

The knob level at the front panel only takes effect over 
analog inputs, and the VU meters do not operate with 
digital signal.

To adjust  the modulation  depth, proceed
like the previous case (MPX preset). 

1.4.2.3 Audio processor locates at 

transmission plant

When   ADA102   links   the   Studios   to   Transmission
Plant,  where   ADA102  DECODER  connects   to   the
audio   processor;   the   audio   level   managed   by
ADA102 link  

is not critical,  

since the processor at

the   end   of   chain   controls   the   level   sent   to   the
transmitter.

In ADA102 CODER, adjust the input gain
to reach 0 VU with signal peaks. If you are
connecting   the   AES-3   input,   the   level
adjustment is no needed (neither possible).

In ADA102 DECODER, adjust the output
level knob to reach 0 VU with signal peaks.
If you are connecting the AES-3 output, the
level   adjustment   is   no   needed   (neither
possible).

Now   follow   the   Audio   Processor   user's
manual in order to adjust the modulation.

1.4.3 Using an RF digital link

The use of a ADA102 CODER in studios connected
to broadband Internet, allows to cover any distance
from studios to  transmitter plant. This solution can be
used to STL links and for radio networks, so one
coder   from   studios   can   send   a   signal   to   several
slaves throughout the country.

Another   solution   to   transport   the   audio   streaming
maintaining the great sound  quality at low cost:   a

microwave link  

for 5.8 GHz (or 2,4 GHz in some

countries) using the standard  802.11.x. This 

band is

free

 in all countries and does not require any special

authorization. It is able to cover 45 Km and should
not have major obstacles between the two sides. 

For details, please contact us (info@solidynepro.com).

SOLIDYNE

ADA102 CODER/DECODER

Page 9

Содержание ADA102





















Отзывы: