Solid RocketWAVE SRF-L-8A1821 страница 24 Скачать руководство пользователя

Страница: 24 / 25

SOLiD RocketWAVE™ SRF-L-8A1821 Product Manual

V1.7 - DEC 2021

Page 24

Troubleshooting

Alarm

LED Operation

Cause

Remedy

Output Upper-limit

- Blinking green while processing the

algorithm

Blinking red while shutting down for

30 mins.

Solid red while fully shutting down

This alarm is raised when output power is

over +2 dB than rated output power.

B20 800MHz : 13 dBm

B3 1800MHz : 15 dBm

B1 2100MHz : 16 dBm

①

Access to the LMT and check input power level.

②

If the power is strong, insert a suitable attenuator into

the coaxial cable between the antenna and the re-

peater.

※

Rated input power range

B20 800 MHz : -54 to -24 dBm

B3 1.8 GHz : -52 to -22 dBm

B1 2.1 GHz : -51 to -21 dBm :

③

If the power is still strong, change the antenna location.

Output Lower-limit

- Solid orange

This alarm is raised when output power is

being lower than lower-limit for 5mins.

①

Access to the LMT and check input power level.

②

Check cable connection status between a Donor An-

tennas.

③

Check the device output lower-limit level is set cor-

rectly.

④

If the input power is normal but the output power

reaches up to lower-limit, check the antenna isolation is

sufficient.

⑤

If the isolation is not sufficient, change the location of

the repeater or turn it away from the donor antenna.

UL Output Upper-limit

- Blinking green while processing the algo-

rithm

- Blinking red while shutting down for 30

mins.

- Solid red while fully shutting down.

This alarm is raised when output power is

over +2 dB than rated output power.

B20 800MHz : 20 dBm

B3 1800MHz : 20 dBm

B1 2100MHz : 20 dBm

①

Access to the LMT and check output power upper-limit

is set correctly.

②

Check the isolation is sufficient.

③

If the isolation is not sufficient, change the location of

the repeater or turn it away from the donor antenna.

Содержание RocketWAVE SRF-L-8A1821























Результаты поиска

Содержание RocketWAVE SRF-L-8A1821

Отзывы:

Похожие инструкции для RocketWAVE SRF-L-8A1821

Бренды по названию

Популярные бренды

Solid RocketWAVE SRF-L-8A1821, Руководство по эксплуатации продукта

Результаты поиска

Содержание RocketWAVE SRF-L-8A1821

Отзывы:

Похожие инструкции для RocketWAVE SRF-L-8A1821

Бренды по названию

Популярные бренды