14
REMOTE CONTROL OPERATING INSTRUCTIONS
1)
Power On and Off
- If the unit is already on, press the
POWER (
I/O
)
button on the remote while point-
ing the remote away from the unit. This will turn the remote on. If the unit is off, now press the
POWER
(
I/O
)
button once to manually turn the unit on. Press the Power button once more to turn the unit off.
When you press the
POWER
button the upper right square on the remote control LCD Display will light
up. When in Air Conditioner, Heating, and Auto mode, the selected temperature will appear on the remote
control display. When the unit is in Fan mode and Dehumidifier mode you will see the “- -” icon instead of
the set temperature. This shows that temperature selection is not available when the unit is in Fan or Dehu-
midifier mode.
2)
Mode Selection
- Press the
MODE
Button repeatedly to cycle between the different modes: Auto, Air
Conditioner, Dehumidifier, Fan only, and Heater mode. The upper left square on the Remote control dis-
play will light up showing which mode is selected. In Air Conditioner mode the display will show
“
COOLING
”, in Heating mode the display will show “
HEAT
”, in Dehumidifier mode the display will
show “
DRY
”, in Fan mode the display will show “
FAN
”, and in Auto mode the display will show
“
AUTO
”.
3)
Fan Speed
- Press the
FAN
speed button to cycle through low, medium, and high fan speeds. The dis-
play on the remote control will show LOW, MED, & HIGH under the “SPEED” label on the remote con-
trol LCD display. There is an additional
auto
speed setting that is enabled in only heating and cooling
modes. This speed is next setting after low when pressing the
FAN
speed button on the remote control.
The speeds will cycle through in this order:
High, Medium, Low, Auto
. Each change in speed will be as-
sociated with a “beep” sound from the unit. The remote control will not display “AUTO” under the speed
label. Once Auto fan speed is selected the unit will beep and there will not be a fan speed displayed on the
remote control.
4)
Temperature Setting
- When the unit is in Air Conditioner or Heating mode you can select your desired
temperature. Press the ▲ or ▼ to select your desired temperature setting. The temperature on the LCD dis-
play on the remote control will increase or decrease accordingly. Pressing the ▼and ▲ buttons simultane-
ously will change the temperature select between °F and °C.
5)
SLEEP MODE
- See “SLEEP MODE” on page 11.
6)
SWING
- To turn on the exclusive WAVEFLO® oscillation, press the
SWING
button on the remote
control. Once you press
SWING,
the louvers on the unit will oscillate up and down. The bottom left
square of the remote control display will show the “ “ icon when WAVEFLO® oscillation (SWING) is
selected.
7)
TIMER
- To program the timer, first press the
T-ON
button. Once
T-ON
is pressed the auto-on timer will
blink in the bottom right rectangle of the remote control display. Press the
MIN
and
HOUR
buttons to
change the clock to the desired time for the unit to automatically turn on. The minutes will increase by 10
with each press of the
MIN
button and the hours will increase by 1 with each press of the
HOUR
button.
Press the
T-OFF
button and the remote control display will flash the desired auto-off timer. Press the
MIN
and
HOUR
buttons to change the clock to the desired time for the unit to automatically turn off. The timer
is set when the auto-off time stops flashing and the words “ON” and “OFF” are displayed next to the time.
8)
CLOCK
- To set the clock on the remote control, hold down either the
MIN
or
HOUR
button until the
displayed time flashes on the remote control display. Change the minutes by pressing the
MIN
button and
change the hours by pressing the
HOUR
button.
