Solectria Renewables PVI 3000 Скачать руководство пользователя | Manualshive

Страница: 33 / 55

background image

PVI 3000/4000/5000/5300

Installation

and Operation Manual

33

3 seconds

↓

Then the LCD will display the setting of the AC high voltage limit above which value, inverter will reduce the output power
until the AC voltage drops within this setting. If the grid type is set to 208/240 with neutral, then the display will be looked
as the figure shown below.

3 seconds

↓

Then the setting of the re-connection time will be displayed. The re-connection time is the duration of delay time for the
inverter to re-connect to the grid after the fault(s) is(are) cleared.

3 seconds

↓

Waiting Mode Display

After the basic information of the inverter is displayed, the system enters the

System Check mode

which is indicated on the

LCD.

During the system checking, if the DC input voltage is not reaching the point of the PV start voltage setting, , then the
following message will be shown on the LCD and the system will stay at this step.

During the system checking, if the grid is not connected to the inverter, then the inverter enters the fault mode and the
following message will be shown on the LCD.

Once system check is done, the inverter goes into the

monitoring mode

. If all data needed for grid feeding is in the acceptable

range, the system will keep monitoring this data for a period of time. The following information tells users that the system will
go into the grid feeding mode in XXX seconds and then show the measured data of the DC input voltages and the existing
voltage and frequency on the grid side.

L o w I n s o l a t i o n

V a c H L i m i t

L - N X X X . X V

V p v S t a r t X X X . X V

R e c o n n e c t X X X s

F a c L X X . X X H z

C l r t < X X X C y c s

M o d e F a u l t

G r i d N A

M o d e

S y s t e m C h e c k i n g

«
...
31
32
33
34
35
...
»

Содержание PVI 3000
























































Отзывы:

Нет отзывов

Похожие инструкции для PVI 3000

VLT Micro Drive FC 51 Series

Бренд: Danfoss Страницы: 28

VLT Micro Drive FC 51 Series

Бренд: Danfoss Страницы: 73

VLT AutomationDrive FC 300

Бренд: Danfoss Страницы: 4

VLT AutomationDrive

Бренд: Danfoss Страницы: 89

Бренд: Parker Страницы: 99

Бренд: Icy Box Страницы: 2

Бренд: Z3 Technology Страницы: 15

Бренд: Furrion net-zero Страницы: 32

Бренд: Patton electronics Страницы: 11

Parallel Port Input/Output Converter PPIO

Бренд: B&B Electronics Страницы: 34

Бренд: StarTech.com Страницы: 24

Бренд: Tvone Страницы: 13

Бренд: Allied Telesis Страницы: 52

Бренд: Patton electronics Страницы: 2

Бренд: Patton electronics Страницы: 7

Бренд: Sencore Страницы: 126

Бренд: DAISHIN Страницы: 28

Бренд: argon audio Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды