E35
ASSEMBLY
INSTRUCTIONS
Dyaco Canada Inc. 2016
10
3
4
UPPER
HANDLE BAR ARMS
See Page 11 for Illustration
1. Connect the Swing Arm (
L-10
) to the left Lower arm (
13
) and connect the
Swing Arm (
R-11
) to the right Lower Arm (
14
) , and secure them with six Hex
Head Bolts (
206
), eight Flat Washers (
164
), four Curved Washers (
181
) and six
Nylon Nuts (
157
) using the Wrenches (
184
&
187
).
2. Connect the two Wires (
L-61
to
62
&
R-60
to
62
) on the L & R sides together
and store the excess wire, including plastic connectors, back inside the
Console Mast (
12
). Place the rubber grommets (
75
) over the wire on each
side and snap them into the holes of the console mast.
PLASTIC
PARTS
See Page 11 for Illustration
Use either screw driver (185 or 186) to secure the following plastic parts.
1. Match up the Console Covers (
94
&
95
) and secure with three Phillips Head
Screws (
139
) and two Sheet Metal Screws (
142
).
2. Match up the Inner Connecting Arm Covers (
111
&
112
). Install the covers
with two Sheet Metal Screws (
142
) and two Phillips Head Screws (
139
) to
each joint.
3. Match up the outer Connecting Arm Covers (
109
&
110
) and install onto the
Left and Right Connecting Arms (
8
&
9
). Secure each side with a Phillips Head
Screw (
139
) and two Sheet Metal Screws (
142
). Make sure you position the
covers with the arrows pointing up. If they are installed incorrectly, they will
break.
4. Install Sliding Wheel Covers (
104
) on each side and secure with four Phillips
Head Screws (
139
).
5. Install the two Stabilizer Covers (
117
&
118
) on the middle stabilizer bar with
two Phillips Head Screws (
139
).
6. Install the Front Stabilizer Cover (
103
) on the front stabilizer with two Phillips
Head Screws (
139
).
7. Install the two incline Cover Brackets (
25
), with the hole for mounting the
plastic cover on the bent tab facing rearward, and secure them on the Incline
Rail Assembly (
2
) with four Phillips Head Screws (
145
). Install the Rear incline
Bar Cover (
115
) on the rail base with two Screws (
139
).
8. Install the Rear Stabilizer Cover (
116
) on the Rear Stabilizer with four Phillips
Head Screws (
139
).
9. Mate the Front Handle Bar Cover (
L-105
) and the Rear Handle Bar Cover (
L-
106
) together on the Left Arm and secure with four Sheet Metal Screws (
142
)
using the Phillips Head Screw Driver (
186
). Repeat the same procedure for #’s
107
&
108
on the right side.
10. This step to be performed after the elliptical power is plugged in. Elevate the
incline to Level 8 and install the Incline Rail Front Cover (
113
) up against the
middle stabilizer tube with four Phillips Head Screws (
139
).
HARDWARE
STEP 3
#75
. Switch Wire Cap
(2 pcs)
#157
. 3/8” x 7T
Nylon Nut (6 pcs)
#164
. 3/8” x 19 x 1.5T
Flat Washer (8 pcs)
#181
. 3/8” x 23 x 2T
Curved Washer (4 pcs)
#206
. 3/8” x 2-1/4”
Hex Head Bolt (6 pcs)
HARDWARE
STEP 4
#139
. M5 x 15mm
Phillips Head Screw
(29 pcs)
#142
. 3.5 x 12mm Sheet
Metal Screw (18 pcs)
#145
. M6 x 10mm
Phillips Head Screw
(4 pcs)
