3
4
6.
2
X3-Matebox
advanced
side connection
5. Monitor the antenna connections of accessories
6.Wiring
Connection
3
6.1 Inverter side connection
- Grid(INV) and EPS(INV)
N16
E-bar
Grid
6.
3
Ground wire connections
The box needs to be grounded as follows.
BAT(+)/BAT(-)
To battery
-
+
- Grid and Load and Battery
Grid(R/S/T/N)
Load(R/S/T/N)
Grid(R/S/T/N)
Load(R/S/T/N)
L=12mm
L
L
L=
12
mm
Grid(INV)
Grid(INV)
R S T N
2122 23 24
EPS(INV)
Grid(INV)
17
18
19
20
PE
N
N26
R S T N
2122 23 24
EPS(INV)
Grid(INV)
17
18
19
N20
PE
A
I
A
I
6.
4
The N-line on the Grid side is short circuited to the N-line on the EPS side
II
B
R S T N
2122 23 24
EPS(INV)
Grid(INV)
17
18
19
20
PE
N
N
25
N26
N-wire connector(130mm,
)
6 mm²
25 26
EPS(INV)
25 26
EPS(INV)
2324
2122
Refer to 6.2
L1
C
L=L1+3mm
C
L=L1+3mm
L1
Diagonal Plier
Grid (PE)
Hexagon keys
Torque: 1.5±0.2N
·
m
-If the user requires wiring rules for neutral wires the standby power supply cannot be isolated or
switched (for wiring Australia and New Zealand regulations AS/NZS_3000:2012)
320102048901
3
) Pass the Grid/Load line through the Grid/Load port of the X3-Matebox
advanced
, then nd the
Grid(R/S/T/N) port and Load (R/S/T/N) ports in the X3-Matebox
advanced
, insert each line, and use the
screwdriver to lock the screws.
4
) Pass the battery power wire through the BAT port of The X3-Matebox
advanced
, then nd the
B
AT+ and BAT- ports in the X3-Matebox
advanced
, insert each wire accordingly, and use the
screwdriver to lock the screws.
6.5 Finally, use the screwdriver to install the baffle back, close the upper cover
and lock
the buckle with a key.
b) Grid(PE) strip the grounding cable insulation(length”L’’), insert the stripped cable into the R type
terminal, and then clamp it.
2) Grid(R/S/T/N/PE) /Load(R/S/T/N) side connection
a) Prepare ordinary
1
0mm² Grid(R/S/T/N/PE) /10mm² Load(R/S/T/N)
and
remove the 12mm insulation
layer at the end of the wire. Insert the European-style terminals respectively.
The stripped terminals must be inserted into the European-style terminals and nally pressed down
with the crimping pliers.
Note: According to the di
ff
erent N terminals of Grid(INV ), select the corresponding
connection position.(if need:(A + 6.4B) or (I + 6.4II))
1) Connect the Grid(INV ) R/S/T/N and EPS (INV ) R/S/T/N/PE ports of the inverter to the X3-Matebox
advanced
port. The connection method is as follows :
a) First, insert the R/S/T EPS(INV ) into the R/S/T port of EPS (INV ) in X3-Matebox
advanced
and the N
EPS(INV ) directly into the hole, directly into the hole and ensure that the installation is tight ;
b) Then nd the Grid(INV ) (R/S/T ) port in X3-Matebox
advanced
, connect the corresponding wire
harness, and lock the screw with a screwdriver.
C) Finally, lock the PE wire/N wire with a hexagonal keys;
According to the BAT(INV )+/BAT(INV )- line symbol on X3-Matebox
advanced
harness, the corresponding
ports of BAT+/BAT- of the inverter are successively inserted.
There is an antenna in the box of monitoring accessories.
a) Install the antenna on the box and tighten it by hand;
b) Then connect the antenna cable to the end of the WiFi
Dongle
.