background image

3

WARNING

• This product is fueled by propane gas. Propane gas is

invisible, odorless, and flammable. An odorant is normally

added to help detect leaks and can be described as a

“rotten egg” smell. The odorant can fade over time so

leaking gas is not always detectable by smell alone.

• Propane gas is heavier than air and leaking propane will

sink to the lowest level possible. It can ignite by ignition

sources including matches, lighters, sparks or open flames

of any kind many feet away from the original leak. Use only

propane gas set up for vapor withdrawal.

• Propane gas should be stored or used in compliance with

local ordinances and codes or with ANSI/NFPA 58. Turn off

propane when not in use.

DANGER

• EXPLOSION - FIRE HAZARD

• Never store propane near high heat, open flames, pilot

lights, direct sunlight, other ignition sources or where

temperatures exceed 120 degrees F (49°C).

• Propane vapors are heavier than air and can accumulate

in low places. If you smell gas, leave the area immediately.

• Never install or remove propane cylinder while heater is

lighted, near flame, pilot lights, other ignition sources or

while heater is hot to touch.

• This heater is red hot during use and can ignite

flammables too close to the burner. Keep flammables at

least 2 feet from sides & 3 feet from top. Keep gasoline and

other flammable liquids and vapors well away from heater.

• The propane cylinder must always be stored outdoors in a

well ventilated space. Never store propane cylinder in an

enclosed area (house, garage, etc.). If heater is to be

stored indoors, disconnect the propane cylinder for outdoor

storage.

Assembly Instructions

Components

Remove all components from package.

Reflector Panel(3)

Reflector Plate

Reflector Stud(3)

Heater Burner

Screen

Head Assembly

Cylinder Housi

Decoration ring

ng

Post

Regulator

Base

Wheel

Gas Hose Less
Regulator

Reflector Assembly

Содержание HSS-A-SHG














Отзывы: