manualshive.com logo in svg

SolarEdge SE10KUS, Руководство по установке, Страница: 44 / 101

Поделиться
Скачать
SolarEdge SE10KUS Скачать руководство пользователя страница 44

Setting the Inverter to Support 208V 3-wire Grid

SolarEdge inverters that support the 208V 3-wire grid  are equipped with two fuse

holders and a fuse in each unit. The position of the fuse configures the AC grid

connection: 4- wire or 3-wire grid connection. By default, the fuse is located in the 4-

wire fuse holder of the inverter, and in the 3-wire fuse holder there is a plastic dummy

fuse.

To set the inverter for 3-wire grid connection, you must move the fuse from the 4-wire

fuse holder, marked as Y GRID, to the 3-wire fuse holder, marked as 

∆

 GRID (see 

Figure 

21).

To set the inverter for 208V 3-wire grid connection:

NOTE

Perform this procedure for all inverter units.

NOTE

Perform this procedure before connecting the inverter to the AC grid.

1.  Remove the inverter cover: Open the inverter cover’s six Allen screws and carefully

pull the cover horizontally before lowering it.

2.  Identify the fuse locations and the markings as described in Figure 21.

Figure 21: Fuse locations and markings

3.  Remove the dummy fuse from the 3-wire grid fuse holder and set it aside.

4.  Move the fuse from the 4-wire grid fuse holder to the 3-wire grid fuse holder.

5.  Place the dummy fuse in the 4-wire grid fuse holder.

6.  During  system setup, set the country to the appropriate 3-wire grid option.  Using

the non-3-wire setting may result in incorrect system operation.

Chapter 4: Connecting the AC and the Strings to the Safety Switch     

43

Three

 

Phase

 

System

 

Installation

 

Guide

 

MAN-01-00527-1.

2

Содержание SE10KUS






































































































Отзывы:

Нет отзывов