Solar Stik PSS-G Скачать руководство пользователя страница 134

Страница: 134 / 141

PSS-G/RAID Alternative Energy System Deployment Guide

August 2020

Solar Stik

Inc.

134

Weights and Dimensions

Observe all Solar Stik case placards. They
indicate the case weight and lift requirements as
prescribed in MIL-STD 1472F.

Figure 74. Case placard

Table 12. Product Weights and Dimensions

Product Weights and Dimensions

Product

Dimensions

Weight

PRO-Verter 7000

19.57 x 24.76 in (49.7 x 62.9 cm)

96 lb (43.5 kg)

Power Hub 2400

8.79 x 24.39 in (22.3 x 62.0 cm)

44 lb (20.0 kg)

Li Expander Pak 2400

24.76 x 13.90 x 19.57 in (62.9 x 35.3 x 49.7 cm)

110 lb (49.9 kg)

PAM Expedition 420 PV Array

Ground Footprint

4 x 10 in (10.16 x 25.4 cm)

PV arrayKit

44 lb (20.0 kg)

Transport Case

48 x 17 x 9 in (121.92 x 43.18 x 22.86 cm)

Transport Weight

76 lb (34.5 kg)

MEP-802A

Dry Weight

800 lb (362.8 kg)

Wet Weight

825 lb (374.2 kg)

Footprint

50.6 x 32 x 37 in (128.5 x 81.28 x 93.98 cm)

Temperature Operating Range for Components

Table 13 contains a listing of the selected Solar Stik products and the overall effective ambient
temperature operating range for each product.

Table 13. Product Operating Temperature Range

Product

Temparature (low) Temperature (high)

Li Expander Pak
2400

-25 °C (-13 °F)

65 °C (149 °F)

Power Hub 2400

-40 °C (-40 °F)

50 °C (122 °F)

PRO-Verter 7000

-20 °C (-4 °F)

50 °C (122 °F)

PAM

-20 °C (-4 °F)

50 °C (122 °F)

SUPPORTING INFORMATION

Содержание PSS-G














































































































































Результаты поиска

Содержание PSS-G

Отзывы:

Бренды по названию

Популярные бренды

Solar Stik PSS-G, Руководство по развертыванию

Результаты поиска

Содержание PSS-G

Отзывы:

Бренды по названию

Популярные бренды