background image

4

GENERAL INSTALLATION MANUAL

PV MODULES: P/M SERIES

any object (e. g., PV module or tools).

 

Do not wear metallic jewelry which can 
cause electric shock during installation.

 

Do not damage the back sheet of PV mo-
dules when fastening the PV modules to a 
support by bolts.

 

Do not damage the surrounding PV mo-
dules or mounting structure when repla-
cing a PV module.

 

Bind cables by the insulation locks. Drooping 
down of cables from the terminal box could 
possibly cause various problems such as 
animal biting, electricity leakage in puddle.

Figure 1 - The components of a module

 

Take proper measures for preventing the 
laminate (consisted of resin, cells, glass, 
back sheet, etc.) from dropping out of the 
frame in case the glass is broken.

 

Cables shall be located so that they will 
not be exposed to direct sunlight after ins-
tallation to prevent degradation of cables.

 

When installing the module, make sure 
that the terminal box is on the higher side 
of the module for better waterproof.

4.  COMPONENTS

5.  SITE SELECTION AND WORK

ENVIRONMENT

 

In most applications, the PV modules 
should be installed in a location where 
there is no shading throughout the year. 
Please make sure that there are no ob-
structions in the surroundings of the site 
of installation.

 

Take proper steps in order to maintain reli-
ability and safety, in case the PV modules 
are used in areas such as: Heavy snow 
areas / Extremely cold areas / Strong wind 
areas / Installations over, or near, water /  
Areas where installations are prone to salt 
water damage / Small islands or desert 
areas.

Содержание M Series
















Отзывы: