Solahart DBV 270 SM Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 68

Solahart DBV 270 SM Скачать руководство пользователя страница 10

ABOUT YOUR WATER HEATER

10

GOING ON HOLIDAYS

It is not necessary to switch off the electrical supply at the power outlet to the water heater if you are going
away. However, if it is necessary to switch off the power to the water heater, refer to

“To Turn Off The Water

on page 9. If the power to the water heater is switched off and there is a risk of freezing, then it is

necessary to drain the gas booster (refer to

“Draining the Gas Booster Water Heater”

on page 9).

HOW DO I KNOW IF THE WATER HEATER IS INSTALLED CORRECTLY?

Installation requirements are

28. The water heater must be installed:

by a qualified person, and

in accordance with the installation instructions, and

in compliance with Standards AS/NZS 3500.4, AS/NZS 3000, AS 5601 or AS/NZS 5601.1, as applicable
under local regulations, and all local codes and regulatory authority requirements.

In New Zealand, the installation must also conform with NZS 5261, as applicable under local regulations, and
Clause G12 of the New Zealand Building Code.

Warning:

Temperature controllers

must not

be fitted to an in-series gas booster as part of a solar water

heater system because water at a temperature much higher than the controller setting can be delivered.

Refer also to

“Pipe Work and Insulation”

on page 7, and to

“Rain Water Tank”

on page 8.

VICTORIAN CUSTOMERS

Notice to Victorian Customers from the Victorian Plumbing Industry Commission. This water heater must be
installed by a licensed person as required by the Victorian Building Act 1993.

Only a licensed person will give you a Compliance Certificate, showing that the work complies with all the
relevant Standards. Only a licensed person will have insurance protecting their workmanship for 6 years.
Make sure you use a licensed person to install this water heater and ask for your Compliance Certificate.

DOES THE WATER CHEMISTRY AFFECT THE WATER HEATER?

The water heater is suitable for most public water supplies, however some water chemistries may have
detrimental effects on the water heater, components and fittings. Refer to

“Water Supplies”

on page 13.

If you are in a known harsh water area or you are not sure of your water chemistry, have your water checked
against the conditions

described on pages

HOW LONG WILL THE WATER HEATER LAST?

The water heater is supported by a manufacturer‟s warranty

. There are a number of

factors that will affect the length of service the water heater will provide. These include but are not limited to
the water chemistry, the water pressure, the water temperature (inlet and outlet) and the water usage
pattern. Refer to

“Precautions”

on page 8.

«
...
8
9
10
11
12
...
»

Содержание DBV 270 SM





































































Отзывы:

Нет отзывов