background image

(9)   Montiere nun das rechte Bein an der 
rechten Seite der Radlerfigur und das Linke 
auf der linken Seite. Das Loch im Fuß wird 
jeweils auf das Pedal geschoben…..

2 x 

2 x 

Ganz wichtig:

Verwechsle nicht das linke
mit dem rechten Bein!

A

B

Linkes Bein
s. (8)

Rechtes Bein s.(8)

Position des Oberschenkels, 

 

:

linkes Bein (?)

„innen“ zum Radlerkörper hin
„außen“ in Richtung Solarzelle

Position des Oberschenkels,

 

:

rechtes Bein (?)

„innen“ zum Radlerkörper hin
Position des Unterschenkel:
„außen“ vom Radlerkörper weg

Linkes Bein

(9)   Now attach the 

 to the 

right leg

right of the cyclist and the 

 to 

left leg

the left side. Slide the hole in each 
foot onto the pedal.

Extremely important:

Do not confuse the left and 

right leg or your cyclist will 

have knock knees!!

2 x 

2 x 

A

B

Thigh position on the left leg: 
"inside", toward the cyclist, lower 
leg position: "outside", toward the 
solar cell:

Thigh position on the right leg: 
"inside", toward the cyclist, lower 
leg position: "outside", away from 
the cyclist:

Attaching the right leg

Attaching the left leg

Left leg

Right leg

Содержание 4037373500406





















Отзывы: