Sokkia iX-1001 Скачать руководство пользователя страница 129 | Manualshive

Страница: 129 / 177

Sokkia iX-1001 Скачать руководство пользователя страница 129

125

19. CHANGING THE SETTINGS

It is possible to allocate the Operating icons in Observation mode to suit the measurement conditions. It is
possible to operate the instrument efficiently because unique Operating icon allocations can be preset to suit
various applications and the ways that different operators handle the instrument.

• The current Operating icon allocations are retained until they are revised again, even when the instrument is

powered OFF.

• Press

[CLEAR]

in <Customize/Select screen> in "19.12 Allocating Operating Icons" " PROCEDURE

Allocating a Operating icon" step 2 to return all customized configurations including Status icon/starkey mode
settings, and screen controls to their previous settings.



• When Operating icon allocations are recorded and registered, the previously recorded key settings are

cleared.

• Operating icons cannot be allocated to "Graphic" displays.



Screens that can be customized and Operating icon allocations when shipped

1. "SHV" and "SHVdist" displays of <Basic observation>

[TRK On] [MOTOR] [0SET] [MEAS]
[SRCH] [EDM] [H-SET] [COORD]
[OFFSET] [RESEC] [REM] [S-O]

2. "Obs." display of <Setting out>

[TRK On] [SHVR] [H.TURN] [MEAS]
[CNFG] [ --- ] [ --- ][REM]
[ --- ] [ --- ] [ --- ] [ --- ]

3. "SHV" and "NEZ" displays of <Set out Coords>

[OK] [TRK On][H.TURN] [MEAS]
[CNFG] [ --- ] [ --- ] [ --- ]
[ --- ] [ --- ] [ --- ] [ --- ]



Functions that can be allocated to the Operating icons
[ --- ]

: No functions set

[MEAS]

: Distance and angle measurement

[0SET]

: Set horizontal angle to 0°

[H-SET]

: Set required horizontal angle

[SHV]

: Switch the "SHV" display and "SHVdist" display (can only be allocated to 1 above)

[L/R]

: Select horizontal angle left/right. The capitalized letter in the Operating icon indicates

the currently selected mode.

[ZA / %]

: Switch between zenith angle/slope in %. The capitalized letter in the Operating icon

indicates the currently selected mode.

[HOLD]

: Hold horizontal angle/release horizontal angle

[CALL]

: Display final measurement data

[HVOUT-S]

: Output angle measurement results to an external device (SET format)

[HVDOUT-S]

: Output distance and angle measurement results to an external device (SET format)

[NEZOUT-S]

: Output coordinates data to an external device (SET format)

[HVOUT-T]

: Output angle measurement results to an external device (GTS format) (can only be

allocated to 1 above)

[HVDOUT-T]

: Output distance and angle measurement results to an external device (GTS format)

(can only be allocated to 1 above)

[NEZOUT-T]

: Output coordinates data to an external device (GTS format) (can only be allocated to 1

above)

[F/M]

: Switch distance units between meters/feet

[HT]

: Set the instrument station, coordinates and instrument height

19.12 Allocating Operating Icons

«
...
127
128
129
130
131
...
»

Содержание iX-1001


















































































































































































Отзывы:

Нет отзывов