manualshive.com logo in svg

Software House iSTAR PRO, Быстрое руководство по установке

Поделиться
Скачать
Software House iSTAR PRO Скачать руководство пользователя страница 2

Overview

2

FIGURE 1. iSTAR Pro Cabinet

TABLE 1. iSTAR Pro Hardware Components

Part Number

Description

Controllers - with Power Supplies

STAR008W-64A

64 MB RAM General Controller Module II with one Access 
Control Module II for up to 8 readers (Wiegand or RM)

STAR016W-64A

64 MB RAM General Controller Module II with two Access 
Control Module II for up to 16 readers (Wiegand or RM)

Controllers - without Power Supplies

STAR008W-64ANPS

64 MB RAM General Controller Module II with one Access 
Control Module II for up to 8 readers (Wiegand or RM)

STAR016W-64ANPS

64 MB RAM General Controller Module II with two Access 
Control Module II for up to 16 readers (Wiegand or RM)

Boards and Accessories

STAR-ACM8-WA

Add-on Access Control Module II (ACM II)

Includes cable assembly and relay board for an additional 8 
Wiegand or 8 RM readers. Each iSTAR Pro can support up to 
2 ACM IIs. 

STARGC-64MBA

General Controller Module II (GCM II), with 64 MB RAM

Enclosure not included.

Содержание iSTAR PRO





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды