Softing BC-700-PB страница 3 Скачать руководство пользователя

Страница: 3 / 60

Table of Contents

PROFIBUS Tester BC-700-PB - User Manual

Table of Contents

Chapter 1

..................................................................................7

Introduction

................................................................................................ 7

1.1

About PROFIBUS Tester 5 BC-700-PB

................................................................................................ 7

1.2

About this document

..................................................................................................................... 7

Purpose

1.2.1

..................................................................................................................... 7

Target group

1.2.2

..................................................................................................................... 8

Conventions used

1.2.3

..................................................................................................................... 8

Document history

1.2.4

................................................................................................ 8

1.3

Scope of delivery

................................................................................................ 9

1.4

Optional accessories

..................................................................................................................... 9

D-sub adapter cable for testing live systems

1.4.1

..................................................................................................................... 10

Adapter set for M12 connection technology

1.4.2

..................................................................................................................... 10

Fieldbus shield digital leakage current clamp

1.4.3

..................................................................................................................... 10

Adapter for testing PROFIBUS PA networks

1.4.4

..................................................................................................................... 11

Spare rechargeable battery

1.4.5

..................................................................................................................... 12

Service interfaces for PROFIBUS DP

1.4.6

....................................................................................................... 12

Connection type D-sub

1.4.6.1

....................................................................................................... 13

Connection type M12

1.4.6.2

................................................................................................ 13

1.5

System requirements

................................................................................................ 14

1.6

Connectors and controls

Chapter 2

..................................................................................15

Prepare device

................................................................................................ 15

2.1

Insert battery

................................................................................................ 16

2.2

Charge battery

Chapter 3

..................................................................................17

Startup

................................................................................................ 17

3.1

Power-up

................................................................................................ 17

3.2

Power-up behaviour without USB connection

................................................................................................ 18

3.3

Power-up behaviour with USB connected

Chapter 4

..................................................................................19

Power-off and sleep mode

Chapter 5

..................................................................................20

Install software and connect to PC

Chapter 6

..................................................................................21

Connection to PROFIBUS

................................................................................................ 21

6.1

General information

..................................................................................................................... 21

Possible side effects when testing a live bus

6.1.1

Содержание BC-700-PB





























































Результаты поиска

Содержание BC-700-PB

Отзывы:

Похожие инструкции для BC-700-PB

Бренды по названию

Популярные бренды

Softing BC-700-PB, Руководство пользователя

Результаты поиска

Содержание BC-700-PB

Отзывы:

Похожие инструкции для BC-700-PB

Бренды по названию

Популярные бренды