Sofar solar 1.1K-3.3KTL-G3 Скачать руководство пользователя страница 63

Страница: 63 / 73

SOFAR 1.1K~3.3KTL-G3

User manual

- 58 -

ID56

PvIsoFault

The insulation

resistance is too low

Check the insulation resistance between the

PV array and earth(ground), if a short circuit

occurs, rectify the fault.

ID57 OverTempFault_

Inv

The inverter temp is

too high

Ensure the installation position and

installation method meet the requirements of

Section 3.4 of this user manual.

Check whether the ambient temperature of

the installation position exceeds the upper limit.

If yes, improve ventilation to decrease the

temperature.

ID58 OverTempFault_

Boost

The Boost temp is

too high

ID59 OverTempFault_

Env

The environment

temp is too high

ID65

Unrecover

HwAcOCP

The grid current is

too high, and has

cause unrecoverable

hardware fault

ID65-ID70 are internal faults of inverter,

turn OFF the “DC switch”, wait for 5 minutes,

then turn ON the “DC switch”. Check whether

the fault is rectified. If no, please contact

technical support.

ID66

Unrecover

BusOVP

The bus voltage is

too high, and has

cause unrecoverable

fault

ID67

Unrecover

IacRms

Unbalance

The grid current is

unbalance, and has

cause unrecoverable

fault

ID68

UnrecoverIpv

Unbalance

The input current is

unbalance, and has

cause unrecoverable

fault

ID69

UnrecoverVbus

Unbalance

The bus voltage is

unbalance, and has

cause unrecoverable

fault

ID70

Unrecover

OCPInstant

The grid current is

too high, and has

cause unrecoverable

fault

ID71

UnrecoverPv

ConfigSetWrong

Incorrect input

mode

Check the input mode(parallel mode/

independent mode) setting of inverter according

to Section 6.3 (C) 6.Input Mode of this user

manual, If it’s incorrect, change it according to

Section 6.3 (A) 10.Set Input mode of this manual

ID74

Unrecover

IPVInstant

The input current is

too high, and has

cause unrecoverable

fault

ID74-ID77 are internal faults of inverter,

turn OFF the “DC switch”, wait for 5 minutes,

then turn ON the “DC switch”. Check whether

the fault is rectified. If no, please contact

technical support.

ID75

Unrecover

WRITE

EEPROM

The EEPROM is

unrecoverable

ID76

Unrecover

READEEPROM

The EEPROM is

unrecoverable

ID77

Unrecover

RelayFail

Relay has happen

permanent fault

Содержание 1.1K-3.3KTL-G3










































































Результаты поиска

Содержание 1.1K-3.3KTL-G3

Отзывы:

Бренды по названию

Популярные бренды

Sofar solar 1.1K-3.3KTL-G3, Руководство пользователя

Результаты поиска

Содержание 1.1K-3.3KTL-G3

Отзывы:

Бренды по названию

Популярные бренды