Snuza Hero MD, Инструкция по эксплуатации

Страница: 14 / 20

English
. 9 SETTINGS
9.1 AudibleTick
This feature causes Hero
MD
to emit an audible ‹tick› on each breathing
movement. To enable the Audible tick, ensure that Hero
MD
is switched ON,
then press the MODE/OFF button (7IYPLÅ`SLZZ[OHU1 second). To increase
the volume of the tick, press the MODE/OFF button once again for medium
]VS\TLHUKHNHPUMVYOPNO]VS\TL;V[\YUVɈIYPLÅ`WYLZZ[OL46+,6--
button a fourth time – Hero
MD
will give a louder beep. This feature may be
used with a baby sound monitor to enable you to ‘hear’ baby’s movements
from a distance.
9.2 Rouse Warning
During monitoring, if no breathing movement is detected for 15 seconds,
Hero
MD
vibrates gently in an attempt to rouse the baby. If breathing movement
YLZ\TLZ^P[OPU[OLUL_[5 seconds, the Breathing Indicator Light (3) will
ÅHZOYLKVULHJOZ\IZLX\LU[IYLH[OPUNTV]LTLU[HZHUPUKPJH[PVU[OH[
there has been an event of no breathing for 15 seconds. With the Rouse
Warning enabled, after 3 such vibration and successful rousing incidents,
the Breathing Indicator Light (3^PSSÅHZOYLKL]LY`2 seconds with a
simultaneous audible beep. This alerts you to the fact that your baby has
stopped breathing for 15 seconds on three occasions and has then resumed
breathing movement after Hero
MD
has vibrated.
Note:- Monitoring will continue while the Rouse Warning is sounding. The
Rouse Warning is automatically enabled each time Hero
MD
is switched ON. To
disable this feature, ensure that Hero
MD
is switched ON, then press and hold
the MODE/OFF button (7) for at least 2 seconds until a tone is heard with a
IYPLM]PIYH[PVUHUKHZPT\S[HULV\ZÅHZOVM[OLYLK)YLH[OPUN0UKPJH[VY3PNO[3)
and Alarm Indicator Light (4). If you want to enable the warning again, switch
Hero
MD
VɈJVTWSL[LS`WYLZZIV[O656--6) and MODE/ OFF (7) buttons
simultaneously), then switch it ON again (the rouse warning is enabled by
default when Hero
MD
is switched on).
9.3 Breathing-rate Warning
The Breathing-rate Warning alerts you if there are less than 8 breathing
TV]LTLU[ZWLYTPU\[L;OL^HYUPUNPZPKLU[PÄLKI`[OL)YLH[OPUN0UKPJH[VY
Light (3ÅHZOPUN`LSSV^^P[OHZPT\S[HULV\ZK\HS[VULH\KPISLILLWL]LY`
second. This feature is automatically enabled each time Hero
MD
is switched
ON. To disable this warning during monitoring, ensure that Hero
MD
is switched
ON, then press and hold the ON/OFF button (6) for more than 2 seconds
until there is a brief double-beep with short vibration and a simultaneous
ÅHZOVM[OL`LSSV^)YLH[OPUN0UKPJH[VY3PNO[3) and Alarm Indicator Light (4).
If you want to enable the warning again, switch Hero
MD
VɈJVTWSL[LS`WYLZZ
both ON/OFF (6) and MODE/OFF (7) buttons simultaneously), then switch it
ON again. The Breathing-rate Warning is enabled by default when Hero
MD
is
switched on.
Page 11