background image

3

Electrical safety

1.  Ground fault circuit interrupter (GFCI) protection should  

be provided on the circuit(s) or outlet(s) to be used for  

this electric chain saw. Receptacles are available having  

built-in GFCI protection and may be used for this  

measure of safety.

2.  Make sure that the mains voltage matches that listed on 

the unit's rating label. Using the improper voltage can 

damage the motor and injure the user.

3.  To prevent electric shock, use only with an extension cord 

suitable for outdoor use, such as SW-A, SOW-A, STW-A, 

STOW-A, SJW-A, SJOW-A, SJTW-A, or SJTOW-A.

  Before use, check that the extension cord is in good 

condition. When using an extension cord, make sure to 

use one heavy enough to carry the current your product 

will draw. An undersized cord will cause a drop in line 

voltage resulting in loss of power and overheating.

4.  To reduce the risk of electric shock, this appliance has a 

polarized plug (i.e. one blade is wider than the other). Use 

this appliance only with a polarized UL-, CSA- or ETL-

listed extension cord recommended for outdoor,  

all-weather use, such as the Snow Joe

®

 + Sun Joe

®

  

SJTW-A 14-gauge 50-foot extension cord with lighted 

end (Model PJEXT50-B). Visit sunjoe.com to purchase 

this extension cord online or, to order by phone, call 

1-866-SNOWJOE (1-866-766-9563).

 

The appliance plug will fit into a polarized extension 

cord only one way. If the appliance plug does not fit 

fully into the extension cord, reverse the plug. If the plug 

still does not fit, obtain a correct polarized extension 

cord. A polarized extension cord will require the use of a 

polarized wall outlet. The extension cord plug will fit into 

the polarized wall outlet only one way. If the plug does 

not fit fully into the wall outlet, reverse the plug. If the plug 

still does not fit, contact a qualified electrician to install 

the proper wall outlet. Do not modify the appliance plug, 

extension cord receptacle or extension cord plug in  

any way.

5.  To prevent the appliance cord from disconnecting from 

the extension cord during operation, use the on-board 

extension cord restraint hook and/or make a knot as 

shown in Table 1.

6.  Do not abuse the cord. Never pull the chain saw by the 

cord or yank the cord to disconnect it from the receptacle. 

Keep the cord away from heat, oil and sharp edges.

Double-Insulated Appliances

In a double-insulated appliance, two systems of insulation 

are provided instead of grounding. No grounding means are 

provided on a double-insulated appliance, nor should a means 

for grounding be added to the appliance. Servicing a double-

insulated appliance requires extreme care and knowledge 

of the system, and should be performed only by qualified 

service personnel at an authorized Snow Joe

®

 + Sun Joe

®

 

dealer. Replacement parts for a double-insulated appliance 

must be identical to the parts they replace. A double-insulated 

appliance is marked with the words “Double Insulation” or 

“Double Insulated.” The symbol     (square within a square) 

may also be marked on the appliance.
 

   DOUBLE-INSULATED: GROUNDING NOT  

 

                  REQUIRED. WHEN SERVICING, USE ONLY    

                 IDENTICAL REPLACEMENT PARTS.

m

          

WARNING 

 

m

Electric shock may cause SEVERE INJURY or 

DEATH. Heed these warnings:

•  Do not allow any part of the electric chain saw to 

make contact with water while it is in operation. If the 

appliance becomes wet while turned off, wipe dry 

before starting. 

•  Use only a UL-, CSA- or ETL-rated extension cord for 

outdoor, all-weather use, such as the Snow Joe

® 

+ Sun Joe

®

 SJTW-A 14-gauge 50-foot extension 

cord with lighted end (Model PJEXT50-B). Visit 

sunjoe.com to purchase this extension cord online 

 

or, to order by phone, call 1-866-SNOWJOE  

(1-866-766-9563).

•  Do not use an extension cord over 100 ft (30 m).
•  Do not touch the appliance or its plug with wet hands 

or while standing in water. Wearing rubber boots 

offers some protection. 

EXTENSION CORD CHART

Cord Length:

Min. Wire Gauge (A.W.G.):

50 ft (15 m)

14

100 ft (30 m)

12

(B) Connect plug and receptacle

Cord set

Appliance cord

(A) Tie cord as shown

Table 1. Method of Securing Extension Cord

Содержание SUNJOE SWJ700E-RM

























Отзывы: