background image

4

4.  To prevent electric shock, use only with an extension cord 

suitable for outdoor use, such as SW-A, SOW-A, STW-A, 

STOW-A, SJW-A, SJOW-A, SJTW-A, or SJTOW-A.

  Before use, check that the extension cord is in good 

condition. When using an extension cord, make sure to 

use one heavy enough to carry the current your product 

will draw. An undersized cord will cause a drop in line 

voltage resulting in loss of power and overheating.

5.  To prevent the appliance cord from disconnecting from the 

extension cord during operation, use the extension cord 

restraint hook and/or make a knot as shown in Table 1.

6.  Do not abuse the cord. Never pull the chain saw by the 

cord or yank the cord to disconnect it from the receptacle. 

Keep the cord away from heat, oil, and sharp edges.

Double-Insulated Appliances

In a double-insulated appliance, two systems of insulation 

are provided instead of grounding. No grounding means are 

provided on a double-insulated appliance, nor should a means 

for grounding be added to the appliance. Servicing a  

double-insulated appliance requires extreme care and 

knowledge of the system, and should be performed only by 

qualified service personnel at an authorized Snow Joe

®

 + 

Sun Joe

®

 dealer. Replacement parts for a double-insulated 

appliance must be identical to the parts they replace.  

A double-insulated appliance is marked with the words 

“Double Insulation” or “Double Insulated.” The symbol     

(square within a square) may also be marked on the appliance.
 

   DOUBLE-INSULATED: GROUNDING NOT  

 

                  REQUIRED. WHEN SERVICING, USE ONLY    

                 IDENTICAL REPLACEMENT PARTS.
This electric chain saw is double-insulated, eliminating the 

need for a separate grounding system. Use only identical 

replacement parts. Read the instructions before servicing 

double-insulated appliances. Use this chain saw only as 

described in this manual.

m

          

WARNING 

 

m

Electric shock may cause SEVERE INJURY or 

DEATH. Heed these warnings:

•  Do not allow any part of the electric chain saw to 

make contact with water while it is in operation. If the 

appliance becomes wet while turned off, wipe dry 

before starting. 

•  Use only a UL-, CSA- or ETL-rated extension cord for 

outdoor, all-weather use. 

•  Do not use an extension cord over

 

100 ft (30 m).

•  Do not touch the appliance or its plug with wet hands 

or while standing in water. Wearing rubber boots 

offers some protection. 

EXTENSION CORD CHART

Extension Cord

Length

Wire Gauge (A.W.G.):

Up to 50 ft

(15 m)

+50 ft - 100 ft

(+15 m - 30 m)

16

14

(B) Connect plug and receptacle

Cord set

Appliance cord

(A) Tie cord as shown

Table 1. Method of Securing Extension Cord

Содержание SUNJOE SWJ698E-RM

























Отзывы: