SNOWJOE SUNJOE SPX2598-MAX, Руководство оператора

Страница: 13 / 20

13
7. Upon completion of detergent application, detach the
detergent tank to clean by removing the two screws that
used to fix the detergent tank (Fig. 21).
8. Run clean water through the detergent tube to remove any
remaining detergent. Then, remove and store for later use.
m
CAUTION!
Damage may occur to painted surfaces if
the detergent is allowed to dry on the surface. Wash and rinse
a small section at a time. Avoid working on hot surfaces or in
direct sunlight.
m
CAUTION!
Failure to follow these cleaning instructions
will cause the injection system to become clogged and
inoperable.
Rinsing with the Pressure Washer
1. Turn off the pressure washer and shut off the water supply.
2. Pull the trigger to release water pressure.
3. Engage the safety lock on the trigger handle by pushing
up on the safety lock until it clicks into the slot (Fig. 17).
4. Remove the soap nozzle by placing your hand over the
nozzle while pulling back on the quick-connect collar.
5. Select the right nozzle for the job (Fig. 22):
I) The 0º intense-jet nozzle (orange) is an extremely
powerful nozzle that delivers a high-pressure,
pencil-point jet stream. It is used to cut heavy dirt
deposits in a small, concentrated area. It is ideal for
dissolving stubborn substances, like tar and grease
spots on concrete, or for removing caked mud from
equipment. Use this nozzle to clean hard-to-reach
areas including the facades of 2-story buildings or the
undersides of lawn mowers and tractors.
NOTE: Care should be used when choosing the
right nozzle to avoid permanently gouging wood or
damaging fragile surfaces.
II) Use the 15º fan-tip nozzle (yellow) for intense cleaning
jobs on hard surfaces. Applications include stripping
paint, removing oil stains, grease, heavy mildew stains,
and rust from steel. This nozzle should only be used in
areas that can withstand the high-pressure from
this nozzle.
III) Use the 25º fan-tip nozzle (green) to clean home siding,
brick patios, wood decks, driveways, or sidewalks.
When using this nozzle, test a small area first to avoid
surface damage.
IV) Use the 40º wide-spray tip nozzle (gray) to clean
items such as cars, trucks, boats, patio furniture,
or lawn equipment.
V) Use the Soap nozzle (black) for low-pressure detergent
application to clean equipment, remove mildew and
oxidation stains from houses, clean bricks or degrease
grimy surfaces.
NOTE: When using detergent, make sure to install the
correct Soap nozzle (black). All of the other colored
nozzles will not work for detergent application.
VI) The rotary turbo nozzle automatically spins a zero
degree spray in a circle at high speed. The spinning
water jet hits the surface area from multiple angles,
quickly breaking down caked-on dirt and grime.
The turbo nozzle can cut cleaning time by up to 40%
6. Start at the top of the area to be rinsed and work your way
down, making sure to overlap your strokes.
m
IMPORTANT!
NEVER USE:
• Bleach, chlorine products, and other corrosive chemicals
• Liquids containing solvents (e.g. paint thinners,
gasoline, oils)
• Tri-sodium phosphate products
• Ammonia products
• Acid-based products
These chemicals will harm the unit and will damage the
cleaning surface.
Shutting down
1. Turn the switch to the OFF/0 position and unplug the
power cord from the outlet.
2. Turn off the water source.
3. Hold the trigger to release water pressure.
Fig. 21
Detergent tank screw Detergent tank screw
15º
SOAP
25º
40º
0º
Fig. 22