background image

9

9. 

Make sure the motor switch is pushed to the OFF (0) 

position before plugging the unit into the power outlet  

(Fig. 9).

Operation

m

IMPORTANT! 

This pressure washer is equipped with 

a micro-switch sensitive to water flow. This Total Stop System 

(TSS) senses water flow in the pump. When the trigger is 

released, water stops flowing through the pump. The TSS then 

automatically turns the motor off to protect the pump from 

overheating, thus saving energy and prolonging pump life.

1. 

Check that the electrical supply voltage and frequency 

(Volt/Hz) correspond to those specified on the pressure 

washer rating plate. If the power supply is correct, you 

may now plug the pressure washer into the power outlet 

(Fig. 10).

 

NOTE: 

The GFCI may need to be reset when first plugged 

into the electric outlet. Press the "Reset" button until the 

power light indicator on the GFCI illuminates.

2. 

Position the washer as CLOSE as possible to the  

water supply.

3. 

The washer must be used on a secure and stable surface 

in a standing, upright position (Fig. 11). 

4. 

Turn the water supply tap on completely.

5. 

Unlock the safety lock, then press the trigger for a few 

seconds until the water flow is steady. Operating the 

pressure washer in this manner will allow air to escape and 

discharge residual pressure in the hose (Fig. 12).

6. 

Keeping the trigger pressed, turn the switch to the ON (I)

position to start the pressure washer.

7. 

When re-starting the motor, always keep the trigger 

pressed.

  NOTE:

 The motor only runs when the trigger is depressed 

and shuts off when the trigger is released.

OFF/0

ON/I

Fig. 9

RESE

T

TEST

Fig. 10

GFCI

Power light 

indicator

Reset

Fig. 11

RELEASE

Fig. 12

Trigger

Safety lock

Push to release

high-pressure hose

Содержание SUNJOE SPX200E-RM



















Отзывы: