SNOWJOE Sunjoe AJP100E, Руководство оператора

Страница: 3 / 12

3
5. Do not abuse the cord. Never pull the Polisher
by the cord or yank the cord to disconnect it from the
receptacle. Keep the cord away from heat, oil and sharp
edges.
6. To reduce the risk of electric shock, this appliance has a
polarized plug (i.e. one blade is wider than the other). Use
this appliance only with a polarized UL-, CSA- or ETL listed
extension cord. The appliance plug will fit into a polarized
extension cord only one way. If the appliance plug does not
fit fully into the extension cord, reverse the plug. If the plug
still does not fit, obtain a correct polarized extension cord. A
polarized extension cord will require the use of a polarized
wall outlet. The extension cord plug will fit into the polarized
wall outlet only one way. If the plug does not fit fully into
the wall outlet, reverse the plug. If the plug still does not
fit, contact a qualified electrician to install the proper wall
outlet. Do not modify the appliance plug, extension cord
receptacle or extension cord plug in any way.
7. Double insulation – In a double-insulated appliance, two
systems of insulation are provided instead of grounding.
No grounding means is provided on a double-insulated
appliance, nor should a means for grounding be added
to the appliance. Servicing a double-insulated appliance
requires extreme care and knowledge of the system,
and should be performed only by qualified service
personnel at an authorized Snow Joe
®
+ Sun Joe
®
dealer.
Replacement parts for a double-insulated appliance must
be identical to the parts they replace. A double-insulated
appliance is marked with the words “Double Insulation”
or “Double Insulated.” The symbol (square within a
square) may also be marked on the appliance.
8. If the replacement of the supply cord is necessary, this has
to be done by the manufacturer or his agent in order to
avoid a safety hazard.
Safety Warnings Common for
Polishing Operations
The manufacturer will not be held responsible for injuries
resulting from incorrect use of the device or from use that does
not comply with the directions.
1. This power tool is intended to function as a polisher.
Read all safety warnings, instructions, illustrations and
specifications provided with this power tool. Failure to follow
all instructions listed below may result in electric shock, fire
and/or serious injury.
2. Operations such as grinding, sanding, wire brushing,
or cutting-off are not recommended to be performed
with this power tool. Operations for which the power tool
was not designed may create a hazard and cause personal
injury.
3. Do not use accessories which are not specifically
designed and recommended by the tool manufacturer.
Just because the accessory can be attached to your power
tool, it does not assure safe operation.
4. The rated speed of the accessory must be at least
equal to the maximum speed marked on the power tool.
Accessories running faster than their RATED SPEED can
break and fly apart.
5. The outside diameter and the thickness of your
accessory must be within the capacity rating of your
power tool. Incorrectly sized accessories cannot be
adequately guarded or controlled.
6. The arbor size of wheels, flanges, backing pads or any
other accessory must properly fit the spindle of the
power tool. Accessories with arbor holes that do not match
the mounting hardware of the power tool will run out of
balance, vibrate excessively and may cause loss of control.
7. Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheels for chips
and cracks, backing pad for cracks, tear or excess wear,
wire brush for loose or cracked wires. If power tool or
accessory is dropped, inspect for damage or install an
undamaged accessory. After inspecting and installing an
accessory, position yourself and bystanders away from
the plane of the rotating accessory and run the power tool
at maximum no-load speed for one minute. Damaged
accessories will normally break apart during this test time.
8. Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron capable of stopping
small abrasive or workpiece fragments.
The eye protection must be capable of stopping flying
debris generated by various operations. The dust mask
or respirator must be capable of filtering out particles
generated by your operation. Prolonged exposure to high
intensity noise may cause hearing loss.
9. Keep bystanders a safe distance away from work area.
Anyone entering the work area must wear personal
protective equipment. Fragments of workpiece or of a
broken accessory may fly away and cause injury beyond
immediate area of operation.
10. Position the cord clear of the spinning accessory.
If you lose control, the cord may be cut or snagged and your
hand or arm may be pulled into the spinning accessory.
(B) Connect plug and receptacle
Cord set Appliance cord
(A) Tie cord as shown
Table 1. Method of Securing Extension Cord