Sno-Way 28V Series Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 32

Sno-Way 28V Series Скачать руководство пользователя страница 20

19

screws and tighten the jam nut to 70 lb-ft. Then place the
lock nut on the cap screw and tighten to 70 lb-ft.

Pivot Frame Assembly:

Install the 1" slotted nut on the threaded end of the special
screw and tighten finger tight. Then tighten the nut
another 2/3 to 1 full turn and line up a slot in the nut with
the cross hole in the special screw. Install the 3/16"x2"
cotter pin in the special screw and spread the ends of the
cotter pin.

Hydraulic Cylinders

To avoid corrosion during storage, coat the exposed
(chrome) portion of the lift and angle cylinders with a light
grease.

Electrical Quick Disconnect Plugs

Install protective caps or plug together quick disconnect
ends to prevent corrosion from forming on terminal ends
during storage or when plow is disconnected from vehicle.

Service Intervals

It is recommended to change the fluid in the hydraulic
system once a season.

Fluid Requirements

IMPORTANT:

Hydraulic unit comes from factory

filled with Type 5606. If additional oil is added it must
be compatible with Type 5606.

NOTE: when Type 5606 is not available Exxon UNIVIS
J13 or equivalent may be used.

Changing Oil and Cleaning Filter Screen

NOTE: We recommend cleaning the filter screen at every
oil change, this will help ensure maximum life and maxi-
mum performance from the pump assembly.

1. Lower plow assembly to ground, put vehicle in park

and turn off engine. Turn hand-held controller off.

2. Remove two (2) self-tapping screws from the front of

the cover and loosen two (2) cap screws from the rear.
Remove the cover.

3. Remove the filler/breather cap from the reservoir.

(See Figure 2-14).

c

CAUTION

• Using the proper oil increases the life

expectancy of the most critical part of your

plow; the Hydraulic power unit.

• Failure to use the proper oil can cause

extensive damage to the power unit, seals and

hydraulic rams.

• Improper oil can cause operating problems and

poor performance in cold weather.

c

CAUTION

Using the proper oil increases the life
expectancy of the most critical part of your
unit; the Hydraulic power unit.

c

WARNING

• Allow the system to cool down before draining

oil or handling system components. Serious

burns can result from contact with hot oil.

• Never disconnect any hydraulic line or fitting

with the unit in the raised position. Always

lower the unit and relieve pressure before

removing any lines or caps.

FAILURE TO HEED CAN RESULT IN INJURY

OR DEATH.

c

WARNING

Ensure engine is OFF and set parking brake
before working on plow. Vehicle movement,
equipment failure or inadvertent operation of
the control switches during maintenance could
result in serious injury

FAILURE TO HEED CAN RESULT IN INJURY

OR DEATH.

«
...
18
19
20
21
22
...
»

Содержание 28V Series

































Отзывы:

Нет отзывов