Sno-Way 26D10000, Руководство владельца по установке и эксплуатации

Страница: 10 / 16

8
The round button in the lower left has no function at this
time, and was designed into the controller for possible
future use
Functions - Joystick V Plow
The joystick controller contains all of the control functions
necessary for the operation of your Sno-Way snowplow.
The joystick on the top left side of the controller controls
the ’Raise’ and ’Lower’ functions. Pulling the joystick
toward you will ’Raise’ the plow. Pushing the joystick
away from you will ’Lower’ the plow. The joystick on the
top right side controls the wings. To move the plow so
both wings angle right, move the joystick to the right. To
move the plow so both wings angle left, move the joystick
to the left. To ’Scoop’ or ’Vee Forward’, push the joystick
away from you. To ’Vee Backward’, pull the joystick
toward you.
Either wing can be moved independently. Pushing the
joystick forward and to the left will move the left wing
forward. Pulling the joystick back and to the left will move
the left wing backward. Pushing the joystick forward and
to the right will move the right wing forward. Pulling the
joystick back and to the right will move the right wing
backward.
There are two buttons on the front of the controller. The
button on the right is the ’Down Pressure’ button. Pressing
the down pressure button will turn on the down pressure
and a red indicator on the top right of the controller will
glow. Pressing the button again will turn the down
pressure off.
The button on the left is the power button. A yellow
indicator light on the top left of the controller will glow
when the controller in ’On’.
Start/Stop Procedure for Controllers
To prevent the controller from inadvertently and
accidentally being switched on or off, a sequence is
required to turn the controller on or off.
To turn the controller ’On’, press the ’On-Off’ or ’Power’
button and ’Down Pressure’ button at the same time. A
green or yellow indicator will glow to indicate that the
controller is ’On’.
To turn the controller ’Off’, press and hold the ’On-Off’ or
’Power’ button for one second. The controller will turn off
and the yellow or green indicator will stop glowing.
Power Saving Mode
The hand held controller uses a very small amount of
electrical current anytime it is ’On’. To minimize current
use when the controller is inactive, the system has a
’Sleep’ mode to shut itself down. If no control function is
pressed for a time period of approximately 60 minutes, the
controller will shut down by itself. When this happens, the
start sequence procedure must be used to re-start the
controller.
Using the Controller to Aid in Mounting and
Removing the Snow Plow
The hand held controller can be used near the snow plow
when mounting or removing the plow with the aid of the
power jackstand.
NOTE: For proper procedure in mounting and removal of
the snow plow, refer to your Sno-Way plow Owner’s
Manual.
For Hard-Wired Units
Disconnect the cable for the hand held controller at the
harness connection inside the vehicle cab and take the
controller to the front of the vehicle. Disconnect the plow
control harness from the vehicle control harness at the
connector at the front of the vehicle. Connect the hand
held controller harness to the plow control harness. The
hand held controller can now be used just as it is normally
used in the cab of the vehicle.
For Wireless Units
Remove the hand held controller from the cab, carry it to
the front of the truck and use normally.
When plow mounting or removal is completed, disconnect
the hand held controller and, if the plow is being mounted,
reconnect the harness of the hand held controller to the
vehicle harness connector in the cab.
WARNING
When using the hand held controller near the
plow, be especially careful of the movement of
any plow components when any switch on the
controller is actuated. Stand clear of the snow
plow at all times to avoid being struck by any
plow parts.
FAILURE TO FOLLOW CAN RESULT IN INJURY
OR DEATH.