manualshive.com logo in svg

Snell IQBRK3048-2A3, Руководство пользователя

Поделиться
Скачать
Snell IQBRK3048-2A3 Скачать руководство пользователя страница 15

IQBRK30

www.snellgroup.com

Card Edge LEDs

Issue 1 Rev 3

Page 15

©

 2013 Snell Limited

4.

Card Edge LEDs

The LEDs on the edge of the module indicate its operating status.

LED

Color

State

Indication

POWER + Green

Illuminated

A positive power supply is present.

POWER -

Green

Illuminated

A negative power supply is present.

CPU OK

Green

Flashing

The CPU is running.

FPGA OK

Green

Illuminated

The unit is booting. LED stays illuminated until the 
SDI is enabled.

Green

Flashing

The FPGA is running.

IN 1 & IN 2 Green

Illuminated

A valid input is present.

REF

Green

Illuminated

A valid reference signal is present.

Green

Flashing

An incorrect frame rate reference is present.

ERR

Red

Illuminated

Board fault conditions. When the module is 
booting, this LED is illuminated until the SDI is 
enabled.

WARN

Yellow

Illuminated

Board warning conditions. LED is illuminated when 
one or more of the SDI inputs is not valid.

OK

Green

Illuminated

The module is operating correctly.

Содержание IQBRK3048-2A3








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды