background image

Do not load this zero-turn rider on a trailer or
truck using two separate ramps. Only use a
single ramp that is at least one foot wider than
the width of the rear wheels of this rider. This
rider has a zero turning radius and the rear
wheels could fall off the ramps, or the rider could
tip over injuring the operator or bystanders.

Operation

10

GENERAL OPERATING SAFETY

Before first time operation:

• Be sure to read all information in the Safety and

Operation sections before attempting to operate this
rider and mower.

• Become familiar with all of the controls and how to

stop the unit.

• Drive in an open area without mowing to become

accustomed to driving the unit.

CHECKS BEFORE STARTING

• Check that the crankcase is filled to full mark on dip-

stick. See the engine owner’s manual for instructions
and oil recommendations.

• Make sure all nuts, bolts, screws and pins are in

place and secure.

• Adjust the seat position, and make certain you can

reach all controls from the operator’s position.

• Fill the fuel tank with fresh fuel. Refer to the engine

owner’s manual for fuel recommendations.

WARNING

Never allow passengers to ride on the unit.

Before leaving the operator’s position for any
reason, lock the motion control levers in the
neutral locked position, disengage the PTO, stop
the engine and remove the key.

To reduce fire hazard, keep the engine, rider and
mower free of grass, leaves and excess grease.
Do not stop or park rider over dry leaves, grass or
combustible materials.

Gasoline is highly flammable and must be
handled with care. Never fill the tank when the
engine is still hot from recent operation. Do not
allow open flame, smoking or matches in the area.
Avoid over-filling and wipe up any spills.

Figure 1. Pre-Start Checks
A. Fuel Tank  Cap
B. Crankcase Oil Fill (Under Engine Cover)
C. Seat Adjustment Knobs

C

A

WARNING

Never operate on slopes greater than 27 percent
(15°).

Select slow ground speed before driving onto a
slope. Use extra caution when operating on
slopes with a rear-mounted grass catcher.

Mow up and down slopes, not across the face,
use caution when changing directions and DO
NOT START OR STOP ON SLOPE.

WARNING

B

WARNING

If you do not understand how a specific control
functions, or have not yet thoroughly read the
FEATURES & CONTROLS section, do so now.
Do NOT attempt to operate the rider without first
becoming familiar with the location and function
of ALL controls.

Содержание Simplicity 2690476





































Отзывы: