Snapper SCRAMBLER YZ16335BVE Скачать руководство пользователя страница 4

 

4

IMPORTANT SAFETY INSTRUCTIONS 

 

MAINTENANCE  

1.  DO NOT store machine or fuel container inside 

where fumes may reach an open flame, spark or 
pilot light such as in a water heater, furnace, 
clothes dryer or other gas appliance. Allow 
engine to cool before storing machine in an 
enclosure. Store fuel container out of the reach 
of children in a well ventilated, unoccupied 
building.  

2.  Keep engine free of grass, leaves or excess 

grease to reduce fire hazard and engine 
overheating.  

3.  When draining fuel tank, drain fuel into an 

approved container outdoors and away from 
open flame.  

4. Check brakes frequently; adjust, repair or 

replace as needed. 

5.  Keep all bolts, nuts and screws properly tight. 

Check that all cotter pins are in proper position.  

6. Always provide adequate ventilation when 

running engine. Exhaust gases contain carbon 
monoxide, an odorless and deadly poison.  

7.  Disconnect negative (black) cable from battery 

before performing maintenance or service. 
Cranking engine could cause injury.  

8.  DO NOT work under machine without safety 

blocks.  

9.  Service engine and make adjustments only when 

engine is stopped. Remove spark plug wire(s) 
from spark plug(s) and secure wire(s) away from 
spark plug(s).  

10. DO NOT change engine governor speed settings 

or overspeed engine.  

11. 

Lubricate machine at intervals specified in 
manual to prevent controls from binding.  

12. Mower blades are sharp and can cut. Wrap the 

blades or wear heavy leather gloves and use 
CAUTION when handling them.  

13. DO NOT test for spark by grounding spark plug 

next to spark plug hole; spark plug could ignite 
gas exiting engine. 

14. 

Have machine serviced by an authorized 
SNAPPER dealer at least once a year and have 
the dealer install any new safety devices.  

15. Use only genuine SNAPPER replacement parts 

to assure that original standards are maintained. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание SCRAMBLER YZ16335BVE






































Отзывы: