background image

 

11

Section 2 - OPERATING INSTRUCTIONS 

 

WARNING 

DO NOT attempt any maintenance, adjustments or 
service with engine and blade running. STOP engine 
and blade. Disconnect spark plug wire and secure 
away from spark plug. Engine and components are 
HOT. Avoid serious burns, allow sufficient time for 
all components to cool. 

 

2.10  INSTALLATION of DISCHARGE DEFLECTOR 
(Optional accessory on some models) 

Install discharge deflector if discharging is desired. Grass 
Bag and Bag Adapter or Recycling Cover must be 
removed. 

1. 

Remove front and rear nuts that secure Bag 

Adapter or Recycling Cover to deck. Refer to 
sections concerning these parts. 

2. 

Install discharge deflector and secure to deck 

using hardware removed in Step 1. Slot in front edge 
of discharge deflector must be under nut as shown 
and both bolts protruding through holes in the side of 
the deflector. Secure nuts to the side of deflector. 
Tighten nuts securely. See Figure 2.17.

 

 

 
 
 
 
 
 
 
 
 
 
 
 

 

 

FIGURE 2.17 

 
 

2.11  INSTALLATION of RECYCLING COVER 
(Optional Accessory on Some Models) 

It will be necessary to remove bag adapter and grass bag 
or discharge deflector before installing recycling cover. 
See previous section for instructions. Install the recycling 
cover and secure to the side and top of the deck with the 
two nuts provided on the machine. Slide top portion of 
cover under nut secured to the deck. See Figure 2.18. 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

FIGURE 2.18 

 

2.12 RECYCLING 

OPERATION 

NOTE:

 For best recycling results, cut up to a maximum of 1/3 of 

grass blade length and recycle ONLY when grass is dry. 

1. 

Set all wheels in the highest cutting position (Notch 6). 

2. 

Move engine speed control to “FAST” (Rabbit) 

position. 

3.

  Move ground speed control to slowest speed setting. 

4.

  Proceed mowing slowly. If grass is very dense, lower 

each rear wheel latch one notch lower than the front 
wheel latches to improve recycling performance. 

 

WARNING 

DO NOT operate without entire Grass Catcher or 
guard in place. Grass Catcher components are 
subject to deterioration during normal use. Inspect 
frequently and replace worn or damaged 
components immediately. 

 

WARNING 

Grass Catcher bags used on SNAPPER products are 
made of woven fabric, and are subject to 
deterioration and wear during normal usage.  Check 
condition of bag before each use.  Immediately 
replace worn or damaged catcher bags with only 
bags recommended by SNAPPER.  The grass catcher 
is optional equipment on some models. 

INSTALL 
DISCHARGE 
DEFLECTOR 

INSTALL  
NUTS 

SLIDE 
DEFLECTOR 
SLOT 

INSTALL RECYCLING 
COVER TO THE DECK 
USING THE TWO NUTS 

RECYCLING 
COVER 

Содержание EP217018BV





























Отзывы: