background image

 

16 

Section 4 - ADJUSTMENTS & REPAIR 

 

4.3.6.  Replacing Bearing In Driven Disc Assembly 
 (Commercial 

Models) 

If the driven disc bearing fails, remove the driven disc 
assembly and replace bearing as follows: 
1.  Using a small flat blade screwdriver, free the clip 
from the transfer rod. Then remove the transfer rod 
from the clip and the speed control rod. Refer to Figure 
4.11. 
2.  Using needle nose pliers, unhook the drive spring 
and slide the driven disc assembly off the hex shaft. 
Refer to Figure 4.12. 
3.  Remove snap ring that secures driven disc hub 
to thrust plate. See Figure 4.15. 
4.  Slide the driven disc hub out of the bearing. 
5.  Remove the four screws that secure bearing. 
6.  Remove bearing and replace with new bearing 
and secure with four retaining screws. 
7.  Reassemble components in reverse order. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

FIGURE 4.15 

 

4.3.7.  Replacing Bearing In Driven Disc Assembly 
 (Non-Commercial 

Models) 

 
IMPORTANT:
 The bearing, on these “M” series Non-
Commercial machines, is staked into the thrust plate. 
The bearing will have to be driven out with a mallet and a 
large punch. A new bearing with four retaining screws 
will have to be purchased to replace existing bearing. 

 
If the driven disc bearing fails, remove the driven 
disc assembly and replace bearing as follows: 
1.  Using a small flat blade screwdriver, free the clip 
from the transfer rod. Then remove the transfer rod 
from the clip and the speed control rod. Refer to Figure 
4.11. 
2.  Using needle nose pliers, unhook the drive spring 
and slide the driven disc assembly off the hex shaft. 
Refer to Figure 4.12. 
3.  Remove both snap rings that secure rubber 
driven disc hub to thrust plate. See Figure 4.16. 
 
 

4.  Slide the rubber driven disc hub out of the 
bearing. 
5.  Drive out existing bearing. 
6.  Install new bearing and secure to thrust plate 
with four retaining screws. Tighten screws securely. 
7.  Reassemble components in reverse order. 

 

 

 

FIGURE 4.16 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

THRUST 
PLATE 

SNAP 
RING 

SHIM 
WASHER 

BEARING 

REMOVE 
FOUR 
MACHINE 
SCREWS 

DRIVEN 
DISC 
PLATE 

DRIVEN 
DISC HUB 

RUBBER 
DISC 

INSTALL 
NEW 
BEARING 

TIGHTEN 
THE FOUR 
SCREWS 

SNAP RINGS 

REINSTALL 
DRIVEN 
DISC 

Содержание EMRP215014B






























Отзывы: