Snapper ELT180H33IBV Скачать руководство пользователя | Manualshive

Страница: 12 / 40

background image

12

Section 2 - OPERATING INSTRUCTIONS

2.4 STOPPING

2.4.3. STOPPING MOWER BLADE
1.

Stop mower blade by moving blade engagement

lever to the "OFF" position. See Figure 2.11.

FIGURE 2.11

WARNING

Once blade is disengaged, it should come to a
complete stop in 5 seconds or less. If the blade
continues to rotate after 5 seconds, the blade brake
must be adjusted. Refer to Section “BLADE BRAKE
ADJUSTMENT” for adjustment procedures or return
machine to dealer for adjustment. DO NOT CONTINUE
to operate mower until blade brake is properly
adjusted.

2.4.4. SETTING PARK BRAKE
1.

Fully depress clutch/brake pedal.

2.

Move park brake lever up into slot. See Figure

2.12.

3.

Release pedal.

FIGURE 2.12

2.4.5. RELEASING PARK BRAKE
1.

Fully depress clutch/brake pedal. Move park brake

lever “DOWN” to release park brake. Release
clutch/brake pedal. See Figure 2.13.

FIGURE 2.13

2.5. CUTTING HEIGHT ADJUSTMENT

1.

Depress lock button on cutting height

adjustment lever. See Figure 2.14.

FIGURE 2.14

2.

Raise or lower deck to any of six positions as

desired.

WARNING

DO NOT park machine on slopes.

OFF

BLADE
ENGAGEMENT
LEVER

PUSH PEDAL ALL
THE WAY DOWN

PARK BRAKE
LEVER

MOVE PARK BRAKE
LEVER “UP” TO ENGAGE
PARK BRAKE

CLUTCH/BRAKE
PEDAL

FULLY DEPRESS
CLUTCH/BRAKE
PEDAL

CUTTING
HEIGHT
ADJUSTMENT
LEVER

DEPRESS
LOCK BUTTON

HIGHEST CUT

LOWEST CUT

PARK
BRAKE LEVER

«
...
10
11
12
13
14
...
»

Содержание ELT180H33IBV









































Отзывы:

Нет отзывов

Похожие инструкции для ELT180H33IBV

Бренд: Baroness Страницы: 199

Бренд: Gardena Страницы: 9

Бренд: Qualcast Страницы: 16

Бренд: Toro Страницы: 52

Бренд: Toro Страницы: 56

Бренд: Gude Страницы: 108

Бренд: Yard-Man Страницы: 42

Бренд: Simplicity Страницы: 14

Бренд: Flymo Страницы: 80

Бренд: AL-KO Страницы: 116

Бренд: Snapper Страницы: 67

Бренд: Land Pride Страницы: 48

Бренд: Tiger Страницы: 230

Бренд: Black & Decker Страницы: 40

Бренд: Black & Decker Страницы: 17

Бренд: Black & Decker Страницы: 16

Бренд: Black & Decker Страницы: 16

Бренд: Black & Decker Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды