Snapper EI55224 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 24

background image

16

Section 4 - REPAIR & ADJUSTMENTS

WARNING

Before attempting any adjustments, maintenance,
service, or repairs, stop engine and auger, always
remove key from ignition switch, remove spark plug
wire and secure wire away from spark plug. Before
tilting machine, drain all the fuel from fuel tank.
Allow engine to run, outdoors where fumes can be
safely dissipated, until all fuel is removed from
carburetor.

4.1.4.  WHEEL DRIVE BELT REPLACEMENT
Inspect belt frequently for signs of excessive wear.
Visually check engine drive belt for cracking,
fraying, severed or belt strands exposed. NOTE:
Auger and Drive Belts are difficult to install. It may
be necessary to allow an authorized Snapper
Dealer to install these belts.
1.  Remove belt cover. See Figure 4.2.
2.  Remove discharge chute.
3.  Loosen belt guide closest to the auger drive belt.
See Figure 4.6.

IMPORTANT: Wheel drive belt will have to be removed
from around engine drive pulley and engine shaft to
install auger drive belt.

4. Remove wheel drive belt from around engine
pulley. See Figure 4.6.

FIGURE 4.6

5. Tilt machine forward to gain access to drive
system area. Secure machine in the tilted position
to prevent tipping over. Remove drive system cover
plate. See Figure 4.7.

FIGURE 4.7

6.  Remove wheel drive belt from drive disc pulley.
Route wheel belt through drive system in between
rubber drive tire and drive disc.
7.  Route new wheel drive belt through drive
system.  NOTE: New belt has to be routed in
between rubber drive tire and drive disc to position it
around auger pulley.
8.  Reinstall wheel drive belt onto engine wheel
drive pulley. Make sure belt is also positioned in the
drive disc pulley groove.
9.  Engage auger control and position belt guide to
have a clearance of 1/8” from auger drive belt.
Tighten belt guide securely.
10.  Reinstall discharge chute, belt and drive system
covers and tighten screws securely.
11.  Reinstall drive system cover plate.
12.  See Sections 4.1.1. & 4.1.2. Auger Belt
Adjustment for new belt adjustment. Adjust belt as
described in these sections.

LOOSEN
BELT
GUIDE

WHEEL DRIVE
BELT

LOOSEN
BELT GUIDE

DRIVE DISC
PULLEY

AUGER DRIVE BELT

REMOVE DRIVE
SYSTEM COVER

«
...
14
15
16
17
18
...
»

Содержание EI55224

























Отзывы:

Нет отзывов

Похожие инструкции для EI55224

Бренд: Finn Страницы: 133

Бренд: Simplicity Страницы: 28

Бренд: Gaggenau Страницы: 28

Бренд: Maguire Products Страницы: 15

4SISON BLB4QL-M

Бренд: Sabre Страницы: 48

Бренд: XPower Страницы: 44

Бренд: Toyama Страницы: 60

Бренд: Cub Cadet Страницы: 28

Бренд: Craftsman Страницы: 27

Craftsman C950-52943-0

Бренд: Craftsman Страницы: 112

Бренд: Boss Страницы: 4

RT3 Undercarriage

Бренд: Boss Страницы: 4

Бренд: Axminster Страницы: 26

AIRDROP P Series

Бренд: Unigreen Страницы: 32

Бренд: Unigreen Страницы: 40

Gladiator 712 + Rider

Бренд: Dustbane Страницы: 19

Gladiator 1050 Ride-On

Бренд: Dustbane Страницы: 28

Бренд: Dustbane Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды