background image

Operation

5

14

Oil Recommendations

We recommend the use of Briggs & Stratton Warranty Certified 

oils for best performance.  Other high-quality detergent oils are 

acceptable if classified for service SF, SG, SH, SJ or higher.  Do not 

use special additives.
Outdoor temperatures determine the proper oil viscosity for the 

engine.  Use the chart to select the best viscosity for the outdoor 

temperature range expected.

*  Below 40oF (4oC) the use of SAE 30 will result in hard starting.
** Above 80oF (27oC) the use of 10W30 may cause increased oil 

consumption.  Check oil level more frequently.

How to Check/Add Oil

Before adding or checking the oil:
• 

Place engine level.

• 

Clean the oil fill area of any debris.

1. 

Remove the dipstick and wipe with a clean cloth.

2. 

Insert and tighten the dipstick.

3. 

Remove the dipstick and check the oil level. It should be at 

the top of the full indicator on the dipstick.

4. 

If low, add oil slowly into the engine oil fill. Do not overfill. 

After adding oil, wait one minute and then recheck the oil 

level.

5. 

Replace and tighten the dipstick.

Fuel Recommendations

Fuel must meet these requirements:
• 

Clean, fresh, unleaded gasoline.

• 

A minimum of 87 octane / 87 AKI (91 RON).  For high 

altitude use, see below.

• 

Gasoline with up to 10% ethanol (gasohol) is acceptable.  

NOTICE: 

Do not use unapproved gasolines, such as E15 and 

E85.  Do not mix oil in gasoline or modify the engine to run on 

alternate fuels.  Use of unapproved fuels will damage the engine 

components and void the engine warranty.
To protect the fuel system from gum formation, mix a fuel 

stabilizer into the fuel. See Off-Season Storage section on 

page 21. All fuel is not the same. If starting or performance 

problems occur, change fuel providers or change brands. This 

engine is certified to operate on gasoline.  The emissions control 

system for this engine is EM (Engine Modifications).

High Altitude

At altitudes over 5,000 feet (1524 meters), a minimum 85 octane 

/ 85 AKI (89 RON) gasoline is acceptable.  To remain emissions 

compliant, high altitude adjustment is required.  Operation 

without this adjustment will cause decreased performance, 

increased fuel consumption, and increased emissions.  Contact 

an authorized Service Dealer for high altitude adjustment 

information.
Operation of the engine at altitudes below 2,500 feet (762 

meters) with the high altitude kit is not recommended.

WARNING!  

POISONOUS GAS HAZARD – Engine 

exhaust contains carbon monoxide, a poisonous gas 

that could kill you in minutes.  You CANNOT smell it, 

see it, or taste it.  Even if you do not smell exhaust 

fumes, you could still be exposed to carbon 

monoxide gas.

• 

Operate this product ONLY outside far away from windows, 

doors and vents to reduce the risk of carbon monoxide gas 

from accumulating and potentially being drawn towards 

occupied spaces. 

• 

Install battery-operated carbon monoxide alarms or plug-in 

carbon monoxide alarms with battery back-up according 

to the manufacturer’s instructions.  Smoke alarms cannot 

detect carbon monoxide gas.

• 

DO NOT run this product inside homes, garages, basements, 

crawlspaces, sheds, or other partially-enclosed spaces even 

if  using fans or opening doors and windows for ventilation.  

Carbon monoxide can quickly build up in these spaces and 

can linger for hours, even after this product has shut OFF.

• 

ALWAYS place this product downwind and point the engine 

exhaust away from occupied spaces.

If you start to feel sick, dizzy, or weak while using this product, 

shut it OFF and get to fresh air RIGHT AWAY.  See a doctor.  You 

may have carbon monoxide poisoning.

Содержание 1696628

























































Отзывы: