Snap-On EEWH311B Скачать руководство пользователя страница 25

Страница: 25 / 28

Page 25

Operation Manual

Check the automatic air lubricator oil level weekly. When

adding oil to the lubricator, disconnect the air supply f rst,

remove the f ll screw ‘

’, and add oil as needed. Make

sure seals are in place when replacing the cap.

553

Fig. 6.0-3

NOTICE!

USE ONLY OILS FOR AIR DEVICES, DO NOT USE
BRAKE FLUID OR OTHER NON-SUGGESTED
LUBRICANTS.

Suggested for the f lter/lubricator unit:

Snap-on Air Tool Oil

IM1PT

J. Grease every 4 months the shaft that connects the

column to the cabinet. Add grease through the greasing

nipple. Fig. 6.0-4

7.1 INSTRUCTIONS FOR DISPOSAL

For waste electrical and electronic equipment

At the time of disposal, at the end of the lifetime of this

equipment, you must:

1. NOT dispose of the equipment as municipal waste and

separate collection is mandatory.

2. Ask the retailer about collection points authorized for regular

disposal.

3. Stick to the standards for correct waste management, to

prevent potential effects on the environment and human

health.

This symbol indicates that separate collection of waste electrical

and electronic equipment is mandatory for scrapping.

Fig. 6.0-4

EEWH311B Air-Electric Tire Changer

Содержание EEWH311B





























Результаты поиска

Содержание EEWH311B

Отзывы:

Похожие инструкции для EEWH311B

Бренды по названию

Популярные бренды

Snap-On EEWH311B, Руководство по эксплуатации

Результаты поиска

Содержание EEWH311B

Отзывы:

Похожие инструкции для EEWH311B

Бренды по названию

Популярные бренды