background image

CONGRATULATIONS!

Thanks for choosing this product. Our aim is to provide you with the highest quality prod-
ucts, and we want you to be totally satisfied with your product and our Customer Service.
If any help or advice is needed, please contact us at 1-888-278-8092. When properly
cared for, this product will give you many years of satisfaction.

GENERAL SAFETY RULES

READ AND FOLLOW ALL INSTRUCTIONS. Failure to fol-

low all instructions in this manual may result in severe personal injury or death.
Keep this manual and refer to it for Safety Instructions, Operating Procedures,
and Warranty.

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS

The safety instructions provided in this manual are not intended to cover all possible
conditions and practices that may occur when operating, maintaining and cleaning
power tools.

Always use common sense and pay particular attention to all the DANGER
WARNINGCAUTION and NOTE statements of this manual.

This is the safety alert symbol. It is used to alert
you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid
possible injury or death.

DANGER indicates an imminently hazardous 
situation which, if not avoided, will result in death
or serious injury.

WARNING indicates a potentially hazardous 
situation which, if not avoided, could result in
death or serious injury.

CAUTION indicates a potentially hazardous 
situation which, if not avoided, may result in
minor or moderate injury.

TABLE OF CONTENTS

CONGRATULATIONS!  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

GENERAL SAFETY RULES  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS  . . . . . . . . 2-3
IMPORTANT INFORMATION ABOUT THIS MANUAL  . . . . . . . . . . . 4
SAFETY WARNINGS AND PRECAUTIONS  . . . . . . . . . . . . . . . . . . . 4-7

FUNCTIONAL DESCRIPTION  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-9

COMPONENT INSTALLATION  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9

OPERATING THE ROUND HEAD NAILER  . . . . . . . . . . . . . . . . . . . . . . . 9-13

SELECT TRIGGER ACTUATION MODE  . . . . . . . . . . . . . . . . . . . . . . 9-11

ADJUSTING DEPTH OF NAILING  . . . . . . . . . . . . . . . . . . . . . . . . . . 11-12

USING THE HOOK  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

LOADING NAILS INTO THE AIR NAILER  . . . . . . . . . . . . . . . . . . . . 12

USING THE NO-MAR NOSEPIECE  . . . . . . . . . . . . . . . . . . . . . . . . . 13

REQUIRED DAILY PREPARATION  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-14

USING THE AIR NAILER  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-16

LOCKING AND UNLOCKING THE TRIGGER  . . . . . . . . . . . . . . . . . . 15

CHANGING DIRECTION OF EXHAUST AIR  . . . . . . . . . . . . . . . . . . . 15

CLEARING JAMS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

MAINTENANCE  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-17

MANDATORY MAINTENANCE   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-19

PARTS DIAGRAM  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-21

PARTS LIST  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-25
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
1 YEAR LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26-28

1

2

Содержание 870010
















Отзывы: