manualshive.com logo in svg

SMSC FlexPWR LAN8710, Техническое описание

Поделиться
Скачать
SMSC FlexPWR LAN8710 Скачать руководство пользователя страница 16

MII/RMII 10/100 Ethernet Transceiver with HP Auto-MDIX and flexPWR

® 

 Technology in a Small Footprint

Datasheet

Revision 1.0 (04-15-09)

16

SMSC LAN8710/LAN8710i

DATASHEET

3.2

  LED Signals

RXER/

RXD4/

PHYAD0

13

IOPD

RXER

 – 

Receive Error

: Asserted to indicate that an error was detected 

somewhere in the frame presently being transferred from the transceiver. 

„

The RXER signal is optional in RMII Mode.

RXD4

 – 

MII Receive Data 4

: In Symbol Interface (5B Decoding) mode, this 

signal is the MII Receive Data 4 signal, the MSB of the received 5-bit 
symbol code-group. Unless configured in this mode, the pin functions as 
RXER.

„

This signal is mux’d with PHYAD0

PHYAD0

 – 

PHY Address Bit 0: 

set the SMI address of the PHY. 

„

See 

Section 5.3.9.1

 for information on the ADDRESS options.

RXCLK/

PHYAD1

7

IOPD

RXCLK

 – 

Receive Clock

: In MII mode, this pin is the receive clock output. 

25MHz in 100Base-TX mode. 2.5MHz in 10Base-T mode.

„

This signal is mux’d with PHYAD1

PHYAD1

 – 

PHY Address Bit 1: 

set the SMI address of the transceiver. 

„

See 

Section 5.3.9.1

 for information on the ADDRESS options.

RXDV

26

O8

Receive Data Valid

: Indicates that recovered and decoded data is being 

presented on RXD pins. 

COL/

CRS_DV/

MODE2

15

IOPU

COL

 – 

MII Mode Collision Detect

: Asserted to indicate detection of 

collision condition. 

CRS_DV

 – 

RMII Mode CRS_DV (Carrier Sense/Receive Data Valid)

 

Asserted to indicate when the receive medium is non-idle. When a 10BT 
packet is received, CRS_DV is asserted, but RXD[1:0] is held low until the 
SFD byte (10101011) is received. In 10BT, half-duplex mode, transmitted 
data is not looped back onto the receive data pins, per the RMII standard. 

MODE2

 – 

PHY Operating Mode Bit 2: 

set the default MODE of the PHY.

„

See 

Section 5.3.9.2

 for information on the MODE options.

CRS

14

IOPD

Carrier Sense

: Indicates detection of carrier. 

Table 3.3 LED Signals 32-QFN

SIGNAL

NAME

32-QFN

PIN #

TYPE

DESCRIPTION

LED1/

REGOFF

3

IOPD

LED1 – 

Link activity LED Indication.

See 

Section 5.3.7

 for a description of LED modes.

REGOFF

 – 

Regulator Off

: This pin may be used to configure the internal 

1.2V regulator off. As described in 

Section 4.9

, this pin is sampled during the 

power-on sequence to determine if the internal regulator should turn on. 
When the regulator is disabled, external 1.2V must be supplied to VDDCR.

„

When LED1/REGOFF is pulled high to VDD2A with an external resistor, the 
internal regulator is disabled. 

„

When LED1/REGOFF is floating or pulled low, the internal regulator is 
enabled (default).

Table 3.2 MII/RMII Signals (continued)  32-QFN (continued) 

SIGNAL

NAME

32-QFN

PIN #

TYPE

DESCRIPTION

Содержание FlexPWR LAN8710
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды