Smiths Medical Oxi-Pulse 30 Скачать руководство пользователя страница 14

Страница: 14 / 66

Chapter 1: Introduction

1-8

Home Use Operation Manual

Cautions

CAUTIOn! Federal (U.S.A.) law restricts this device to sale by or on the order of a physician.

CAUTIOn!

Do not disassemble unit, not user serviceable. Refer to qualified service

personnel.

CAUTIOn! Failure to charge the monitor while the monitor is in long term storage may

shorten the battery life. Charge the monitor while it is in storage to ensure the

longest battery life.

CAUTIOn! Due to limitations of the li-Ion chemistry, the rechargeable battery pack

should not be charged at ambient temperatures above 45 °C (113 °F) or

below 5 °C (41 °F).

CAUTIOn! The WW1090 rechargeable battery pack is shipped with only 30% of full charge.

The battery pack must be charged completely before use.

CAUTIOn! The WW1090 rechargeable battery pack utilizes li-Ion secondary cells. Dispose

of spent batteries in compliance with your institution’s guidelines and local

ordinances.

CAUTIOn! Observe proper battery polarity (direction) when replacing batteries.

CAUTIOn! Do not allow water or any other liquid to spill onto the monitor or Docking

Station. Do not autoclave, ethylene oxide sterilize, or immerse the monitor or

Docking Station in liquid. evidence that liquid has been allowed to enter the

monitor or Docking Station voids the warranty.

CAUTIOn! Where the equipment has accidentally gotten wet, it should be wiped dry

externally and allowed to dry thoroughly before use.

CAUTIOn! before cleaning or disinfecting the printer, unplug the AC adapter, remove the

batteries and remove the paper.

CAUTIOn! Do not allow printer paper to become wet. If the printer paper gets wet remove

the paper immediately. Do not use the printer until the paper is replaced.

CAUTIOn! Chemicals used in some cleaning agents may cause brittleness of plastic parts.

Follow cleaning instructions in this manual.

CAUTIOn! Cleaning with disinfectants, including alcohol, may shorten the life of the plastic

or electronic parts; but appropriate disinfection must still be performed.

CAUTIOn! Pressing any key with sharp or pointed instruments may permanently damage

the keypad. Only press keys with your finger.

Содержание Oxi-Pulse 30


































































Результаты поиска

Содержание Oxi-Pulse 30

Отзывы:

Похожие инструкции для Oxi-Pulse 30

Бренды по названию

Популярные бренды

Smiths Medical Oxi-Pulse 30, Руководство по эксплуатации для домашнего использования

Результаты поиска

Содержание Oxi-Pulse 30

Отзывы:

Похожие инструкции для Oxi-Pulse 30

Бренды по названию

Популярные бренды