Главная
/
Smith
/
FS351 Series
/
Сборка

Smith FS351 Series, Сборка

Поделиться

1
2
3
4
5
6
7
8
9
10

Страница: 6 / 10

background image

6

Drum Installation

Sideplate Removal

• Remove the six (6) bolts and washers using a 9/16” socket – do not impact.

• Ensure the correct high-speed or clutch kit is installed.

• Remove side plate using handles, or gently pry.

• Remove existing drum and spacers if installed.

• Inspect shaft for any rounding or deformation.

«
...
4
5
6
7
8
...
»

Содержание FS351 Series











Отзывы:

Нет отзывов

Похожие инструкции для FS351 Series

Бренд: Fender Страницы: 15

Бренд: J D Squared Страницы: 18

Бренд: Zetec Страницы: 23

Бренд: p-light Страницы: 28

Бренд: H-TEC Education Страницы: 16

Бренд: H-TEC Education Страницы: 12

Бренд: tayco Страницы: 111

Бренд: Maeda Страницы: 276

Бренд: Olympus Страницы: 56

Бренд: quadient Страницы: 14

Бренд: Qu-Bit Electronix Страницы: 31

Бренд: JBSYSTEMS Light Страницы: 17

Бренд: Sota Страницы: 7

Бренд: MAKSIWA Страницы: 155

Tacx Boost Bundle

Бренд: Garmin Страницы: 12

Бренд: ZAMST Страницы: 14

Бренд: AVID LABS Страницы: 20

Бренд: Briteq Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды