background image

COSMOS DRIVER SERIES 3000 - USE AND MAINTENANCE MANUAL

2  GENERAL WARNINGS

These   assembly   instructions   are   an  integral   part   of  the  equipment,  and   must   be  kept   for   future  reference    until

decommissioning. 
The user should be informed that the present instructions reflect the state of the art at the moment when the equipment

was sold; they will remain fully acceptable despite subsequent upgrades based on new experiences.

DO NOT  USE THE  EQUIPMENT,  NOR  MAKE  ANY  INTERVENTION  BEFORE INTEGRALLY

READING AND UNDERSTANDING THIS MANUAL.

IN PARTICULAR, ADOPT ALL SAFETY PRECAUTIONS AND PRESCRIPTIONS INDICATED IN THIS MANUAL.

THE EQUIPMENT CANNOT BE USED FOR PURPOSES DIFFERENT THAN THE ONES DESCRIBED IN THIS

MANUAL; SMITEC S.p.A. SHALL NOT BE HELD RESPONSIBLE FOR ANY DAMAGES, INCONVENIENCES OR

ACCIDENTS DUE TO THE NON-COMPLIANCE WITH THESE PRESCRIPTIONS.

In order to make the manual consultation easier, the following symbols have been adopted:

Indication of “PROHIBITED ACTION”.

The symbol "DANGER" is used when the non-respect of the prescriptions or the tampering of organs

can cause serious harm to people or things.

The indication "DANGER FROM HOT SURFACES" is used when the non-respect of the prescriptions

can cause serious damage to people or things.

The   indication   "DANGER   FROM   ELECTRIC   SHOCK"   is   used   when   failure   to   comply   with   the

prescriptions can cause serious harm to people.

The symbol “USE OF INDIVIDUAL PROTECTIONS” means that protective gloves must be worn

The indication "USE PPE" protective glasses.

Indication of “INFORMATION OF PARTICULAR RELEVANCE”.

Ver. 1.07

Pag. 7

Содержание Cosmos 315 Series











































































































Отзывы: