Smeg SIMU530, Руководство пользователя

Страница: 9 / 12

10
COOKTOP CARE TROUBLESHOOTING
General Cleaning
IMPORTANT: Before cleaning, make sure all controls are off
and the cooktop is cool. Always follow label instructions on
cleaning products.
Soap, water and a soft cloth or sponge are suggested first
unless otherwise noted.
CERAMIC GLASS
To avoid damage, do not use steel wool, abrasive powder
cleansers, chlorine bleach, rust remover or ammonia.
Cleaning Method:
Always wipe with a clean, wet cloth or sponge and dry
thoroughly to avoid streaking and staining.
Cooktop cleaner is recommended for regular use to help avoid
scratches, pitting and abrasions, and to condition the cooktop.
It may be ordered as an accessory.
A cooktop scraper is also recommended for stubborn soils.
Light to moderate soil
■
Paper towels or clean damp sponge.
■
Cooktop cleaner and clean damp paper towel:
Clean as soon as cooktop has cooled down. Rub
creme into surface with a damp paper towel or soft
cloth. Continue rubbing until white film disappears.
Sugary spills (jellies, candy, syrup)
■
Cooktop scraper:
Clean while the cooktop is still warm. You may want to
wear oven mitts while cleaning the cooktop.
Heavy soil, dark streaks, specks, and discoloration
■
Cooktop cleaner or nonabrasive cleanser:
Rub product into soil with a damp paper towel or soft
cloth. Continue rubbing until white film disappears.
Burned-on soil
■
Cooktop cleaner and Cooktop scraper:
Rub creme into soil with damp paper towel. Hold
scraper as flat as possible on surface and then scrape.
Repeat for stubborn spots. Polish entire cooktop with
creme and paper towel.
Tiny scratches and abrasions
■
Cooktop cleaner:
Rub creme into surface with a damp paper towel or
soft cloth. Continue rubbing until white film disappears.
Scratches and abrasions do not affect cooking performance
and after many cleanings become less noticeable.
Try the solutions suggested here first in order to avoid the
cost of an unnecessary service call.
Nothing will operate
■
Is the cooktop wired properly? See the Installation
Instructions for more information.
■
Has a household fuse blown, or has a circuit breaker
tripped? Replace the fuse or reset the circuit breaker. If the
problem continues, call an electrician.
Cooktop will not operate
■
Is the cooktop control set correctly? Touch the display
area on the control panel to select a cooking surface before
selecting a function.
■
Is the “Control Lock” Cooktop Lockout set? See “Control
Lock” section.
■
Has the cooktop turned off by itself?
The power off key
was unintentionally touched. Press power key again. Reset
the cooktop.
Excessive heat around cookware on cooktop
■
Is the cookware the proper size? Use cookware about the
same size as the surface cooking area. Cookware should
not extend more than ½" (1.3 cm) outside the cooking area.
Cooktop cooking results not what expected
■
Is the proper cookware being used? See “Cookware”
section.
■
Is the cooktop control set to the proper heat level?
See “Cooktop Controls” section.
■
Is the cooktop level? Level the cooktop. See the
Installation Instructions.
Display shows messages
■
Is the display flashing when you place a saucepan
on an induction surface cooking area? Check that the
saucepan is electromagnetic. Check that the diameter of
the saucepan is large enough. Center the saucepan on the
surface cooking area. Allow the saucepan to cool down in
the event that it has become hot when used. Switch the
surface cooking area off and then on again. If the display
still does not light up, turn power off at the circuit breaker.
Wait 20 seconds and turn power back on.
■
Is the Performance boost function display flashing and
switching off? The Performance boost function operates
the surface cooking area with the most power. During long
cooking times, it is possible that the function will switch
the surface cooking area off to keep the cooktop from
overheating. You can continue to use the cooktop if the
display is not flashing.