background image

 

 

 

Instructions for the User

 

 

 

18 

8.

 

Cleaning and maintenance 

 

 

Before carrying out any operations, disconnect the appliance from the 

electricity supply.

 

8.1

 

Cleaning stainless steel 

 

 

To keep the hob in good condition, it must be cleaned regularly, after each use, first 
allowing it to cool. 

8.1.1

 

Routine daily hob cleaning 

When cleaning and caring for stainless steel surfaces, always use 

only

 specific 

products which do not contain abrasives or chlorine-based acids. 

Instructions for use:

 pour the product onto a damp cloth and wipe over the surface, 

then rinse thoroughly and dry with a soft cloth or chamois leather. 

 

8.1.2

 

Food stains or spills 

Never use metal scouring pads or sharp scrapers which will damage the 
surface.  
Use ordinary non-abrasive products for steel, with the aid of non-scratching 
sponges and wooden or plastic utensils if necessary. 
Rinse thoroughly and dry with a soft cloth or chamois leather. 

 

 

 

 

8.2

 

Cleaning the components 

8.2.1

 

The knobs 

 

The knobs and front panel must be cleaned with a soft cloth dipped in warm water and 
dried thoroughly. The knobs can easily be removed by pulling them outwards. 

 

 

Never clean the knobs or front panel with aggressive products containing alcohol or 
steel or glass cleaners, since they might cause permanent damage. 

 

8.2.2

 

Pan stands and burners 

 

Remove the pan stands and wash them in warm water with a non-abrasive detergent, 
taking care to remove all deposits. Put them back on the hob. 
These components must never be washed in a dishwasher. 

 

8.2.3

 

The flame diffuser rings 

 

The burner caps and flame diffuser rings can be removed for easier cleaning; wash 
them in hot water and non-abrasive detergent, taking care to remove all deposits, and 
wait for them to 

dry completely.

  

The burner pins 

A

 must be fitted into the recesses 

B

 in the flame diffuser ring. The 

holes 

C

 in the flame diffuser ring must mate with the ignition plugs and thermocouples 

D

 on the hob. 

NEVER REMOVE THE FIXING RINGS TO CLEAN THE HOB. 

 

8.2.4

 

The plugs and thermocouples 

 

For best performance, the ignition plugs and thermocouples must always be kept 
thoroughly clean. Check them frequently and if necessary clean them with a wet cloth. 
Remove any dry residues with a wooden toothpick or a needle. 

 
 
 
 

914773334/ C

 

Содержание PTSA605-3

















Отзывы: