5019 612 10095
Prewash cycle increases programme duration approximately 15 min. Consumption values were measured in normalized
conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in
the table in relation to the water supply pressure and temperature, the load and the type of wash.
The data on the “Energy Label” refer to the programme “Cotton 60°C”.
* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the
water out.
1. Load the machine, close the drum flaps and check
that they are properly locked.
2. Add detergents and additives into the dispenser
to no more then the “MAX” level mark, as
follows:
•
Programme with pre and main wash
•
Main wash programme without prewash
•
Fabric softeners and conditioners
•
Chlorine bleach
•
Stain remover agents
•
Anti-scale agents (if necessary)
3. Turn the programme selector knob to the
desired programme.
4. Turn the temperature selector knob to the
desired temperature.
5. Press the spin speed reduction button, if
desired.
•
If you want to cancel the final spin, select the rinse
hold option and drain the water after the cycle
has finished (see Appliance in “Rinse Hold”).
Selecting or deselecting an option can be done
at any time during the programme. The option
will be applied as long as the corresponding
programme phase has not been executed yet.
“Rinse Hold” button
• The laundry remains in the last rinse water without
progressing to the final spin cycle to avoid creasing
and prevent colours from fading.
• This option is particularly recommended for the
“Synthetic” or “Delicate” programmes.
• This function is particularly useful if you want to
postpone spinning to a later time, or if you want to
drain only.
Appliance in “Rinse Hold”:
• Press the “Rinse Hold” button again: the programme
will terminate automatically with the selected spin cycle.
• If you do not wish to spin the clothes, press the
“On/Off” button, turn the programme selector
knob to the “Drain” programme and press the
“On/Off” button again.
CONSUMPTION DATA
Programme
Temperature Selector
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. Programme
Duration
(hours : minutes)
Cotton
95
5.0
63*
1.80
2:05
Cotton
60
5.0
55
0.95
2:05
Cotton
40
5.0
55
0.55
2:05
Synthetic
60
2.0
56
0.80
1:30
Synthetic
40
2.0
56
0.40
1:30
Delicate
40
1.5
60
0.55
0:45
Wool
40
1.0
60
0.50
0:40
Silk
30
1.0
60
0.30
0:50
PREPARATION OF WASH CYCLE
SELECT THE DESIRED OPTION
“Intensive Rinse” button
• One rinse cycle is added to ensure a more
intensive rinse.
• This option is particularly suitable for areas with
very soft water, washing baby linen and people
with detergents allergies.
“Half Load” button
• Can be used for small loads and lightly soiled
laundry.
• Reduces the water consumption especially
during the rinses.
Turn on the tap and press the “On/Off” button.
The indicator light of the “On/Off” button lights
up.
Note: If there is a power interruption or if the
appliance is disconnected during the cycle, the
programme will run again from the point where it
was interrupted.
• The programme selector knob is in the Stop
position “
”.
1. Press the “On/Off” button to switch off the
machine.
2. Cancel the options.
3. Turn the tap off.
4. Wait for the door to unlock (about 1 minute).
5.
Open the door and the drum flaps and unload
the machine.
1. Switch off the machine by pressing the
“On/Off” button.
2. Select the new programme.
3.
Start programme by pressing the “On/Off”
button again.
If, for any reason, you wish to interrupt the
programme for a certain time and continue it later:
1. Press the “On/Off” button.
2. After the desired pause, press again the
“On/Off” button.
1. Switch off the machine by pressing the
“On/Off” button.
2. Set the programme selector to “Drain”.
3. Press the “On/Off” button again to start the
“Drain” programme.
PROGRAMME START
END OF WASH CYCLE
CHANGE THE PROGRAMME DURING THE
WASH CYCLE
PAUSE/INTERRUPT A PROGRAMME
CANCEL PROGRAMME
