background image

 

18

Remove the filters 

A, B, C

 (simply lift them out as shown 

here), taking care that no large residues fall into the sump 
underneath.  Clean them to remove residues and rinse 
with plenty of water, then put them correctly back in 
place; do not use sharp or pointed tools.

 

Clean away any limescale deposits to prevent excessive 
build-ups; 

 

If possible, leave the door ajar when not in use;  

 

Clean surfaces thoroughly and often with a damp 

cloth; use neutral, non-abrasive detergents which 
do not use chlorine compounds, which corrode 
and damage stainless steel. 

 

A

B

C

 

Do not use the products mentioned above even when cleaning the floor underneath or in the vicinity of the 
dishwasher, to ensure that fumes or drops cannot damage the steel surfaces.  

IMPORTANT:

 The dishwasher 

automatically performs program “P0”

 at the start of the day if

 water has been 

left in the tank

 and has dropped below the temperature of 40°C

 

 

11.2 Periodic checks 

Remove the top and bottom spray arms by unscrewing the central screw and unscrew the caps from the ends of 
the rinsing arms as shown. 

Do not unscrew the nozzles.

 

Clean the holes and nozzles under a jet of clean running water; do not use tools which might cause damage. 
Reassemble the spray arms with care.

 

 

 

 

 

 

Clean the outside of the appliance with a damp cloth and neutral soap, rinsing and drying thoroughly. 
 

11.3  Lengthy periods out of use 

If the dishwasher is to be out of use for a fairly long period of time,

 the detergent and rinse aid dispenser 

devices must be emptied to prevent crystallisation and damage to the pumps:   

Remove the intake hoses 

from the detergent and rinse aid containers and place them in a container of clean water, then perform a few wash 
cycles followed by a complete pump-out.

 

 

Finally, turn off the master switch, close the water intake valve and leave the door ajar until the interior is 
completely dry.  The detergent and rinse aid intake hoses must be put back into the containers when the 
dishwasher is returned to service, 

taking care not to swap them over 

 (red hose = detergent, blue hose = rinse 

aid). 

Содержание CWC600DL
























Отзывы: