SMC Networks ZK2 A Series страница 56 Скачать руководство пользователя

Страница: 56 / 80

-55-

No. ZK2-OM01301

9. Specifications

■

General Specifications

Ambient temperature range

(No condensation)

-5 to 50

C (Without pressure sensor and pressure switch, With pressure switch,

With pressure switch with energy saving function)

0 to 50

C (With pressure sensor)

Fluid

Air

Vibration resistance

Note 1)

30m/s

(Without pressure sensor and pressure switch, With pressure sensor)

20m/s

(With pressure switch)

Impact resistance

Note 2,3)

150m/s

(Without pressure sensor and pressure switch, With pressure sensor)

100m/s

(With pressure switch)

Standard

CE, RoHS

Note 1) The characteristics are satisfied when tested for 2 hours in each of the X, Y and Z directions at 10 to 500 Hz without

energization. (Initial value)

Note 2) The characteristics are satisfied when tested one time in each of the X, Y and Z directions without energization. (Initial

value)

Note 3) For valve type R (Self-holding release valve linked), impact resistance is 50m/s

■

Valve Common Specifications

Valve model

Note 4)

ZK2-VA

□K□□A

ZK2-VA

□R□□A

ZK2-VA

□J□□A

Type of

Actuation

Note 5)

Supply valve: N.C.

Release valve: N.C.

Supply valve: Self-holding release

valve linked

Release valve: N.C.

Supply valve: N.C.

Release valve: None

Valve configuration

Pilot operated dual 2 port

Pilot operated 2 port

Operating

pressure

range

0.3 to 0.6 MPa

Valve construction

Poppet seal

Manual override

Push type

Rated voltage

24 VDC, 12VDC

Power consumption

0.35W

Lead wire

(

ZK2-LV-

□□-A

)

Conductor cross section: 0.2 mm

(AWG24)

Insulator O.D.: 1.4 mm

Note 4) Refer to Valve assembly on

page 33

for the valve model number.

Note 5) ZK2-VA

□R: When the supply valve is energized (20 ms or more), the supply valve keep ON position even after

energization is stopped. When release valve is energized, the supply valve is turned off in conjunction with the
operation of the release valve.

ZK2-VA

□K: Supply valve turns off when is not energized. Select this type when pressure switch with energy saving

function is used.

■

Noise Level (Reference values)

Model

ZK2

□07 ZK2□10 ZK2□12 ZK2□15

Noise level

[dB(A)]

ZK2G (High-noise reduction silencer exhaust)

ZK2A (Silencer exhaust)

Содержание ZK2 A Series

















































































Результаты поиска

Содержание ZK2 A Series

Отзывы:

Похожие инструкции для ZK2 A Series

Бренды по названию

Популярные бренды

SMC Networks ZK2 A Series, Руководство по эксплуатации

Результаты поиска

Содержание ZK2 A Series

Отзывы:

Похожие инструкции для ZK2 A Series

Бренды по названию

Популярные бренды