SMC Networks ZK2 A Series Скачать руководство пользователя

Страница: 54 / 80

-53-

No. ZK2-OM01301

8.2.5. Filter case maintenance

1) When the filter case is dirty, it can be removed and cleaned.

To remove the filter case, insert a precision screwdriver into the groove of the release lever and push in

direction (1), and slide the filter case in direction (2).

Note 1) Surface A of the filter case is the sealing surface when vacuum is generated. Handle with care so that the surface is not

scratched or damaged.

Note 2) Filter case is made of polycarbonate. Avoid chemicals such as thinner, carbon tetrachloride, chloroform, acetic ester,

aniline, cyclohexane, trichloroethylene, sulfuric acid, lactic acid, water base cutting fluid (alkaline).

Note 3) Do not expose the filter case to direct sunlight for a long period of time.

(Procedure to put parts back together)

2) Make sure that the body gasket that matches the product specifications is installed correctly onto the

ejector. If they are out of the place, vacuum leakage may occur.

One check valve type

(All specifications other than vacuum switch with energy saving function and

exhaust interference prevention valve)

Two check valve type

(Vacuum switch with energy saving function and exhaust interference

prevention valve

Body gasket

Содержание ZK2 A Series

















































































Результаты поиска

Содержание ZK2 A Series

Отзывы:

Похожие инструкции для ZK2 A Series

Бренды по названию

Популярные бренды

SMC Networks ZK2 A Series, Руководство по эксплуатации

Результаты поиска

Содержание ZK2 A Series

Отзывы:

Похожие инструкции для ZK2 A Series

Бренды по названию

Популярные бренды