SMC Networks ZK2 A Series Скачать руководство пользователя

Страница: 49 / 80

-48-

No. ZK2-OM01301

8. Maintenance

8.1. Maintenance

Implement the maintenance and check shown below in order to use the ejector and the vacuum

pump system safely and in an appropriate way for a long period of time.



Maintenance should be performed according to the procedure indicated in the Operation Manual. Improper

handling can cause damage and malfunction of equipment and machinery.



Maintenance work

Compressed air can be dangerous when handled incorrectly. Therefore, in addition to observing the product

specifications, replacement of elements and other maintenance activities should be performed by personnel

with sufficient knowledge and experience pertaining to pneumatic equipment.



Draining

Remove condensate from air filters and mist separators regularly. If the collected drainage is drained to the

downstream side, it can stick inside of the product, causing operation failure and failure to reach the specified

vacuum pressure.



Replace the filter element built into the ejector and the vacuum pump system and the silencer regularly.

(Refer

to the replacement procedure below.)

It is recommended to replace the filter element and the silencer when the pressure drop reaches 5kPa as a

guideline. The replacement cycle varies depending on the operating conditions, operating environment and

supply air quality.

However, if there is a vacuum pressure drop and/or delay in the vacuum (adsorption) response time which

causes problem with the settings during operation, stop the operation of the product and replace the element

regardless of the above mentioned replacement guideline.

5) Operation in an environment where there is a lot of dust in the air

The processing capacity of the filter element built into the product may be insufficient. It is recommended to

use SMC's air suction filter (ZFA, ZFB, ZFC series) in order to avoid problems beforehand.

6) Check before and after the maintenance work

When the product is to be removed, turn off the power supply, and be sure to cut off the supply pressure and

exhaust the compressed air. Confirm that the air is released to atmosphere.

When mounting the product after the maintenance work, supply compressed air, connect to the power, check

if it functions properly and have a leakage inspection. Especially for valve type R, be sure to check that the

supply valve is OFF in the initial condition because it is possible that it is ON due to vibration.

7) Do not disassemble or modify the product, other than the replacement parts specified in this manual.

8) Tighten to the specified tightening torque.

If the tightening torque is exceeded, the product, the mounting screws, brackets and the pressure switch

can be broken. Insufficient torque can cause displacement of the product and the pressure switch from each

proper position and loosening of the mounting screws.

Содержание ZK2 A Series

















































































Результаты поиска

Содержание ZK2 A Series

Отзывы:

Похожие инструкции для ZK2 A Series

Бренды по названию

Популярные бренды

SMC Networks ZK2 A Series, Руководство по эксплуатации

Результаты поиска

Содержание ZK2 A Series

Отзывы:

Похожие инструкции для ZK2 A Series

Бренды по названию

Популярные бренды