background image

Preparation for Communication

 

INR-244-831 

 

1-1 

Preparation for Communication 

Make preparation for using communication facility as follows.   

 

1) Turn off the power switch of Thermo-con. (Detach the communication connector when the power 

switch of the thermo-con is turning off.) 

2) Connect communication cable to communication connector of Thermo-con. 

Use twist pair shield cable as communication cable. 

Connect the host and thermo-con with the straight cable for RS-485. 

Connect shielded cable of communication cable to communication connector and drop it to FG(flame 

ground). 

Connection drawing for communication is shown in the Figures 1-1. 

Length of communication cable for RS-485 shall be limited to around 500[m] in total 

If communication cable for RS-485 is longer, connect terminating resistance (220

Ω

,1/2w) to each    + 

and - terminal of the host computer and the farthest Thermo-con. 

3) Turn on the power switch of Thermo-con. 

4) Set the communication method (page 2-1) for all Thermo-con connected. (Refer the operation 

manual (HEC-OM-Y008) how to set the communication method parameters.) 

5) 

That’s all for preparation of communication. Then if a communication command from the host

 

 

computer is given, each Thermo-con will respond. 

 

Figure1-1 Communication Connection

 

Содержание Thermo-con INR-244-831























Отзывы: