SMC Networks IZN10E Series, Руководство по эксплуатации

Страница: 34 / 37

Doc. no.IZ
＊
-OMV0005
33
7. Specifications
IZN10E-
□
IZN10E-
□
P
(NPN) (PNP)
Energy saving nozzle
High flow rate nozzle
Fluid
Operating pressure
Note 3),Note 4)
Tube O.D.
Discharge stop signal
Reset signal
External switch signal 1
External switch signal 2
Discharge signal
Error signal
Maintenance signal
Housing
Nozzle
Emitter
Energy saving nozzle
High flow rate nozzle
Female threads for piping
L-bracket
Pivoting bracket
DIN rail mounting bracket Single unit
Models
Ion generation method Corona discharge
Method of applying voltage High frequency AC type
Applied voltage
Note 1)
2.5kVAC
Offset voltage
Note 2)
(ion balance)
+/- 10V
+/- 15V
Air purge
Air (Clean dry air)
0.05 to 0.7 MPa
ø6
・
ø1/4 inch
Ambient humidity
（
During operation/storage
）
35 to 65% Rh (With no condensation)
Power supply voltage 24VDC+/-10%
Current consumption 80mA or less
Input signal
Connected to 0 V
Voltage range: 5 VDC or less
Current consumption: 5mA or
less
Connected to +24 V
Voltage range: 19 VDC to
power supply voltage
Current consumption: 5mA or
less
Output signal
Maximum load current: 40 mA
Residual voltage: 1 V or less
(Load current at 40 mA)
Maximum applied voltage: 26.4 VDC
Maximum load current: 40 mA
Residual voltage: 1V or less
(Load current at 40 mA)
40g
Standard / Directive CE (EMC directive 2014/30/EC)
Stainless steel
Tungsten
Material
Weight of the body
Weight of the bracket
ABS, Stainless steel
Impact resistance
100m/s
2
70g
70g
75g
30g
Effective static neutralization distance 20 mm to 500 mm
Ambient temperature
（
During operation/storage
）
0 to 55
o
C
40g
Note 1)
Value measured with probe of 1,000MΩ and 5pF.
Note 2)
Note 3)
Note 4) If air purging is stopped during operation temporarily, turn the discharge stop signal input OFF to prevent the increase of ozone
concentration in the nozzle.
Note 5) Refer to cautions on page 9 if IZN10E-11
□□□
-
□
(Female threads for piping) is used.
Charge elimination is not possible without air purge. Air has to be purged during ion generation to avoid adverse effect on the
product and peripheral equipment due to the increase of ozone concentration in the nozzle.
Measurement values based on a charged plate (dimensions: 150 x 150 mm, electrostatic capacity: 20pF) defined by ANSI standard
(ANSI/ESD STM3.1-2006). Distance between charged plate and ionizer: 100 mm, Air purge: 0.3 MPa (energy saving nozzle) / 0.1 MPa
(high flow rate nozzle).
IZN10E-C
□
-
□
100 to 240 VAC, 50/60 Hz
24 VDC
1 A max
When used
0 to 40
o
C
Storage
-20 to 60
o
C
Ambient humidity During operation/storage 10 to 90
％
RH
CE, cUL
Output voltage
Output current
Ambient temperature
Applicable standard / directive
Models
Input voltage
Note 6)
Note 6) For AC cable type, the rated voltage of the AC cable included in accessories is 125 V. (Page 12).