Using The EZ 3Click Wizard
SMCGS16-Smart / SMCGS24-Smart
EZ Switch™ 10/100/1000 16/24-Port
Smart Gigabit Switches
EZ Switch™ 10/100/1000 16/24-Port
Smart Gigabit Switches
EZ Switch™ 10/100/1000 16/24-Port
Smart Gigabit Switches
EZ Switch™ 10/100/1000 16/24-Port
Smart Gigabit Switches
EZ Switch™ 10/100/1000 16/24-Port
Smart Gigabit Switches
Initial Configuration
Hardware Installation
Menu Overview
Troubleshooting
Using The EZ 3Click Wizard
SMCGS16-Smart / SMCGS24-Smart
SMCGS16-Smart / SMCGS24-Smart
SMCGS16-Smart / SMCGS24-Smart
SMCGS16-Smart / SMCGS24-Smart
EZ Switch™ 10/100/1000 16/24-Port
Smart Gigabit Switches
Initial Configuration
Hardware Installation
Menu Overview
Troubleshooting
If you forget your password or the IP address of your SMC Smart Switch, you will be
unable to access the Web Management Interface. If this happens you can recover by
taking the following steps:
1. Remove the power cord from the back of the Switch.
2. Remove all cables from the front-panel ports.
3. Connect port 1 to port 2, on the front panel, using a standard network cable.
4. Reconnect the power cord to the rear of the Switch.
5. Wait at least 40 seconds before disconnecting port 1 from port 2
Note that, after following this procedure, all of the switch’s configuration – including
password and IP address will be reset to factory defaults; the password will be
ssm
mc
ca
ad
dm
miin
n and the Switch IP address will be reset to 119
92
2..116
68
8..2
2..110
0.
To make use of the management features of your SMC Smart Switch you must first
give it an IP address. For simplicity, this should be done before you permanently
install the switch in the network.
The following procedure is recommended:
1. Place your Smart Switch close to the PC that you will use to configure
it. It will help if you can see the front panel of the switch while working
on your PC.
2. Connect the Ethernet port of your PC to any port on the front panel of
your Smart Switch, start your PC (if it is not already running), connect
power to the switch and, when your PC has finished its start-up
sequence, verify that you have a link by checking the LEDs on the
front-panel of the switch (see the Hardware Description for more
information).
3. The default IP address of the switch is 192.168.2.10 and the subnet mask
is 255.255.255.0. If your PC has a different address from the switch but
is on the same subnet (i.e. the PC and switch both have addresses that
start 192.168.2.x but are different thereafter) you can skip directly
to step 4. Otherwise you will have to set your PC’s IP address manually.
If you are unfamiliar with this process, please refer to of the User
Guide.
4. After changing your PC's IP address, open your web browser and enter
the address h
httttp
p::////119
92
2..116
68
8..2
2..110
0.. If your PC is properly configured, you
will see the login page of your Smart Switch. If you do not see the login
page, please check your settings and repeat step 3.
5. Enter the password (the default is ssm
mc
ca
ad
dm
miin
n) and click on the L
Lo
og
giin
n
button.
6. Click on the S
SY
YS
ST
TE
EM
M menu-choice then click on L
LA
AN
N S
Se
ettttiin
ng
gss when it
appears. On the L
LA
AN
N S
Se
ettttiin
ng
gss page, enter the IP address, Subnet Mask
and Gateway IP Address for the switch then click on the A
AP
PP
PL
LY
Y button.
No other configuration changes are required at this stage but it is recommended that
you change the administrator’s password before logging out. To change the password
click on the SYSTEM¬ Password menu-choice and fill in all the fields on the P
Pa
assssw
wo
orrd
d
S
Se
ettttiin
ng
gss page before clicking on the A
AP
PP
PL
LY
Y button.
Using The EZ 3Click Wizard
SMCGS16-Smart / SMCGS24-Smart
EZ Switch™ 10/100/1000 16/24-Port
Smart Gigabit Switches
Initial Configuration
Initial Configuration
Hardware Installation
Menu Overview
Troubleshooting
Using The EZ 3Click Wizard
SMCGS16-Smart / SMCGS24-Smart
EZ Switch™ 10/100/1000 16/24-Port
Smart Gigabit Switches
Initial Configuration
Hardware Installation
Menu Overview
Menu Overview
Troubleshooting
All of the configuration of your SMC Smart Switch will be done using the Web,
Management Interface. If you are familiar with the concepts of a Managed Layer 2
switch, you should have no problem navigating the user interface; just open your
Web Browser, enter the address of the switch, login and you are ready to go
(http://192.168.2.10 is the default address and smcadmin is the default password).
The screenshot on the right shows the first page that you will see after logging in.
The page is laid out as follows:
•
At the top of the screen is the front-panel image. Ports on the image turn green
to show that the port is connected to a network device. If you allow your mouse
to hover over a port , the port-number will be displayed.
•
On the left of the screen is the Menu. Single-clicking on a Menu-choice will
change the page displayed on the right-hand (Main Page) side of the screen.
•
The content of the Main Page (on the right) will change when you make
different Menu choices. The Main Page is where switch parameters are
displayed and edited. Not all pages can be edited but, where parameters can
be changed, you will find three buttons at the bottom of the page; H
HE
EL
LP
P,
A
AP
PP
PL
LY
Y and C
CA
AN
NC
CE
EL
L. Use the H
HE
EL
LP
P button if you are unsure what you need
to do. None of your edits will be saved until you click on the A
AP
PP
PL
LY
Y button and
you can use the C
CA
AN
NC
CE
EL
L button to discard all your edits.
If you are new to managed switches, see the User Guide for a detailed
explanation of:
•
Configuring ports and diagnosing network problems.
•
Creating and configuring Trunks (Link Aggregations) to improve network
resilience and throughput.
•
Adding ports to VLANs to improve network security.
•
Configuring Quality Of Service to improve the throughput of key
applications(e.g.VoIP)
M
Ma
aiin
n P
Pa
ag
ge
e
M
Me
en
nu
u
T
To
op
p b
ba
arr,,
d
diissp
plla
ay
yiin
ng
g tth
he
e
ffrro
on
ntt--p
pa
an
ne
ell
iim
ma
ag
ge
e
Using The EZ 3Click Wizard
SMCGS16-Smart / SMCGS24-Smart
EZ Switch™ 10/100/1000 16/24-Port
Smart Gigabit Switches
Initial Configuration
Hardware Installation
Menu Overview
Troubleshooting
Troubleshooting
